Reference: RBD-0676

MQ-7 Carbon Monoxide Gas Sensor

6 reviews

Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm. RoboticsBD

Reference: RBD-0822

Hall Effect Sensor Switch Magnetic Detector Module For Arduino

8 reviews

S49E hall sensor Features wide-range voltage comparator LM393 Signal output indicator Analog / Digital output

Reference: RBD-1177

4-20mA Signal Generator Current Loop Simulator Tester

1 review

This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...

Reference: RBD-1974

Brand: DFRobot

Gravity Huskylens AI Camera Vision Sensor with Silicone Case

2 reviews

One-click learn Machine Learning Enabled Onboard Screen Extreme Performance

Reference: RBD-0677

MQ-8 Hydrogen Gas Sensor

5 reviews

Using high-quality dual-panel design, with power indicator and TTL signal output instructions. The switching signal having a DO (TTL) output and analog output AO. TTL output valid signal is low. The higher the voltage, the concentration of the analog output voltage is higher. A hydrogen gas detection with good sensitivity. Has a long life and reliable...

Reference: RBD-1192

Hall Effect Sensor 6851/A3144

8 reviews

Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.

Reference: RBD-1424

ZMCT103C 5A Range Single Phase AC Micro Current Transformer Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-2125

QRE1113 Reflective Optical Sensor

1 review

Phototransistor output  No contact surface sensing  Miniature package

Reference: RBD-0132

TCRT5000L Reflective Optical Sensor

30 reviews

The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...

Reference: RBD-0575

PH Meter Digital Tester Aquarium Pool Water Urine Wine LCD Pen Monitor Protable

7 reviews

Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration

Reference: RBD-0678

MQ-9 Gas Leakage Detection Sensor

3 reviews

Good sensitivity to CO/Combustible Gas High sensitivity to Methane, Propane, and CO Long life and low cost Simple drive circuit Input voltage: DC 5±0.2V Current Consumption: 150mA

Reference: RBD-0680

9 Degrees of Freedom Breakout- MPU9250

5 reviews

Acceleration, Gyroscope Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g 9 DOF modules. RoboticsBDChinese Variant MP92 QFN24 PackageThe magnetometer is currently inaccessible via I2C and therefore unavailable.True 9dof: Gravity 10 DOF IMU AHRS BNO055 + BMP280 True 9dof:...

Reference: RBD-1199

Hall Effect Sensor A1302 49E

5 reviews

Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance 

Reference: RBD-1675

PZEM-004T V3.0 AC Digital Multifunction Meter Watt Power Volt Amp With Coil 100A

2 reviews

Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0

Reference: RBD-0665

Rain & Steam Detection Sensor Module

23 reviews

Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation

Reference: RBD-0679

MQ-135 Gas Sensor

20 reviews

Sensitivity to Ammonia, Sulfide and Benzene steam Sensitive for benzene, alcohol, smoke Fast response and recovery Adjustable sensitivity. RoboticsBD Signal output indicator Output voltage boosts along with the concentration of the measured gases increases.

Reference: RBD-0687

BMP280 Pressure Sensor Module

17 reviews

Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V. Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C). Peak current: 1.12mA. RoboticsBD Operating Pressure: 300 hPa to 1100 hPa. Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.

Reference: RBD-1208

Laser Receiving Sensor

7 reviews

Working Voltage: 5V DC Operating Temperature: -30ºc ~ 85ºc Output high level when received the laser signal Output low level when not receive laser signal. Application: Electronic Circuits

Reference: RBD-1835

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-050 50A

1 review

Input current (RMS): 50A. Work temperature: -25℃～+70℃. Storage temperature: -30℃～+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.

Reference: RBD-2215

4 Channel Infrared Line Following and Obstacle Sensor

1 review

Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.