Reference: RBD-0022

Ultrasonic Sonar Sensor HC-SR04

284 reviews

This is the HC-SR04 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC (Power),...

Reference: RBD-2321

Red 2WD Aluminum Smart Robot Car Chassis Kit

1 review

Red 2WD Aluminum Smart Robot Car Chassis Kit with durable 5051 aluminum alloy frame Equipped with two powerful DC gear motors for independent wheel control Lightweight and low-cost platform ideal for beginners and hobbyists Supports easy integration of sensors and microcontrollers like Arduino Features 60mm silicone tire wheels for stable and smooth motion

Reference: RBD-1388

Cap Conductive Slip Ring 4 Wire

2 reviews

A slip ring is an electromechanical device that allows the transmission of power and electrical signals from a stationary to a rotating structure. A slip ring can be used in any electromechanical system that requires rotation while transmitting power or signals. It can improve mechanical performance, simplify system operation and eliminate damage-prone...

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-0578

Robotics Claw Mechanical Gripper Clamp Kit

4 reviews

The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm

Reference: RBD-0357

GY-ML8511 Ultraviolet Light UV Sensor Module

3 reviews

Operating voltage (VCC): 3 V to 5V Operating current: 120μA (typical) 190μA (max) Operating Temperature: -40°C ~ +85°C Photodiode sensitive to UV-A and UV-B Embedded operational amplifier Analog voltage output Low supply current (300uA type) and low standby current (0.1uA type) RoboticsBD

Reference: RBD-2513

5V Electromagnet - 25 Kg Holding Force - P40/20

Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...

Reference: RBD-2215

4 Channel Infrared Line Following and Obstacle Sensor

1 review

Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.

Reference: RBD-3560

Aluminum GT2 Timing Pulley – 20 Teeth, 3.17mm Bore

This Aluminum GT2 Timing Pulley with 20 teeth and a 3.17mm bore is a precision component crafted for accurate motion transfer in belt-driven systems such as 3D printers, CNC machines, and engraving equipment. Designed to pair seamlessly with 2GT/GT2 timing belts of 6mm width, it enables smooth and reliable rotational-to-linear motion conversion from a...

Reference: RBD-0122

4WD N20 Gear Motor Chassis

2 reviews

Designed for speed with four-wheel drive capabilities Reduce drag with two-wheel drive configuration N20 Gear Versatile Compact 

Reference: RBD-0274

Brand: Waveshare

Raspberry Pi 5inch Resistive Touch HDMI LCD

5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch :  Raspbian 5 inch HDMI with Touch Download Link    

Reference: RBD-0296

Servo Wheel with Thick Rubber Tire

2 reviews

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 75 mm Width : 15 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow 1 pcs

Reference: RBD-1551

N20 Ball Caster with 3/8″ Metal Ball

7 reviews

Metal Balls with ABS housings 3/8" diameter size Two spacers (1/16" and 1/8" thick) Easy to assemble

Reference: RBD-0041

Smart Speed Detecting Sensor for Arduino

4 reviews

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-1301

Multi-Chassis - Rescue Platform Complete Kit

Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high

Reference: RBD-0919

TP4056 Lithium Battery Charger Module With Protection Dual Functions

68 reviews

Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-0032

Arduino Nano

112 reviews

USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...

Reference: RBD-0659

Digital Line Following Sensor - 8 Array

6 reviews

Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD

Reference: RBD-0716

65mm Rubber Wheel with 25GA Motor Mounting Bracket

4 reviews

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.

Reference: RBD-1336

ESP8266 5V WIFI Relay Smart Home Remote Control Switch

3 reviews

Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...

Reference: RBD-0227

JF-0530B Pull Push Type Electric Solenoid Electromagnet 10mm 5N DC6V

4 reviews

Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm

Reference: RBD-0394

Senring M220-06 Medium Capsule Slip Ring with Silver-Plated Teflon AWG26 Wires

They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD

Reference: RBD-0360

Polulu RP5 Tracked Chassis Gray

Durable plastic body 6-AA battery holder included two brushed DC motors with 210 mA free run and 2.4 A stall current at 7.2 V maximum speed of 6 in/s (15 cm/s) at 7.2 V

Reference: RBD-3205

TT Motor Bi-Metal Gearbox Double-Sided Axle with 1:90 Gear Ratio

2 reviews

The TT Motor Bi-Metal Gearbox with a 1:90 Gear Ratio is a durable and cost-effective solution for robotics and motion-driven projects. Featuring a double-sided axle and steel-reinforced gears, this motor offers higher torque at slower rotational speeds, making it ideal for applications where strength and durability are essential. The bi-metal construction...

Reference: RBD-0180

Brand: SparkFun Electronics

Makey Makey Kit

Description: This is the same product as the Makey Makey Standard Kit. The difference is this version comes in fancy clamshell packaging meant for our distributors that need it. Regular customers are welcome to order, but we want to limit the amount of extra packaging finding its way into the trash heap.

Reference: RBD-0411

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino

2 reviews

Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD

Reference: RBD-0653

Male Pin Header Single Row (L Shaped)

44 reviews

Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)

Reference: RBD-0166

XBee 1mW Trace Antenna - Series 1 (802.15.4)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Reference: RBD-0915

UART EM4100 RFID Card Reader RDM6300

4 reviews

Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design

Reference: RBD-0023

HC-SR501 PIR Motion Sensor

112 reviews

Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default)  Work temperature: -20-+80°C