Reference: RBD-0147

HR202 Humidity Detection Sensor Module

5 reviews

Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).

Reference: RBD-0151

Flame Sensor Fire Detection Module

59 reviews

Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...

Reference: RBD-0357

GY-ML8511 Ultraviolet Light UV Sensor Module

3 reviews

Operating voltage (VCC): 3 V to 5V Operating current: 120μA (typical) 190μA (max) Operating Temperature: -40°C ~ +85°C Photodiode sensitive to UV-A and UV-B Embedded operational amplifier Analog voltage output Low supply current (300uA type) and low standby current (0.1uA type) RoboticsBD

Reference: RBD-0431

Formaldehyde/ Formalin Detection Sensor CJMCU-1100 MS1100

2 reviews

Working temperature : -10℃ ~ 50℃ Working humidity : below saturation point Storage temperature : -20℃ ~ 80℃ RoboticsBDPCB Color: Red or Purple 

Reference: RBD-0163

HSM-20G Analog Temperature & Humidity Sensor

4 reviews

Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V    Output voltage range (corresponding to 0-100%RH) DC 1-3.19V    Test accuracy 5% RH

Reference: RBD-0423

5 Way Flame/Fire Sensor

2 reviews

Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.

Reference: RBD-0425

GY-9960LLC APDS-9960 RGB and Gesture Sensor Module

1 review

Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD

Reference: RBD-0429

BH1750FVI Digital Light intensity Sensor

9 reviews

High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface

Reference: RBD-0493

RTD PT-100 Temperature Sensor 100mm Probe -50‑400℃

6 reviews

Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;

Reference: RBD-0671

MQ-2 Flammable Gas & Smoke Sensor

68 reviews

Operating Voltage:+5V Preheat Duration:20 s Analog Output Voltage:0 to 5 V Dimension:36x20x21 mm. RoboticsBD

Reference: RBD-1111

Geiger Counter Kit Nuclear Radiation Detector Gamma Ray Build Radiation Monitoring Station

1 review

This is one open-source Geiger Counter project which could be used to detect nuclear radiation. The schematic and code and other helpful files are listed in this package. All the codes are designed and tested on this kit, these materials are useful for DIY Geiger Counter Kit Nuclear Radiation Detectors or Radiation Monitoring Stations. Note: The kit comes...

Reference: RBD-1347

TTP223 Capacitive Touch switch Digital Touch Sensor Module For Arduino

7 reviews

TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.

Reference: RBD-0319

K Type Thermocouple Sensor Probe for Temperature Controller

2 reviews

Type K Type.  Mounting thread: M6  Temperature Range:0-600°C. RoboticsBD

Reference: RBD-0426

GUVA-S12SD UV Detection Sensor Module

5 reviews

Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity

Reference: RBD-0663

TTP223B Digital Touch Sensor Capacitive Touch

12 reviews

Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD

Reference: RBD-0672

MQ-3 Alcohol Gas Sensor

9 reviews

Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output:  0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.

Reference: RBD-0823

Optical Sensitive Resistance Light Detection Photosensitive LDR Sensor Module

39 reviews

LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)

Reference: RBD-3529

Brand: DFRobot

RS485 Photoelectric Solar Radiation Sensor (400-1100nm)

The RS485 Photoelectric Solar Radiation Sensor is designed to measure solar radiation in the spectral range of 400-1100nm. It uses the photoelectric principle to convert sunlight into electrical signals. Featuring a highly sensitive photosensitive element and a wide-spectrum absorption range, the sensor delivers accurate solar radiation measurements.

Reference: RBD-0320

MAX6675 Module + K Type Thermocouple Sensor (Arduino Compatiable)

11 reviews

Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C):-30°C - 150 °C Cold Junction Compensation Range(°C):...

Reference: RBD-0416

TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino

Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output