- There are no more items in your cart
- Shipping Free
- Total BDT 0

Flight Controller
Have you thought of building your own Flight controller? Then, Robotics Bangladesh is the right place to understand and build your own Flight controller for your Quadcopter or your Arduino.
Reference: RBD-0300
Arducopter APM 2.8 Flight Controller + Ublox NEO 7M GPS with Compass
Model: APM 2.8 Arducopter APM 2.8 Flight Controller Input Voltage (V): 12-16 V. Arducopter APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 Arducopter APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 Ublox NEO 7M GPS Tracking sensitivity: 161 dBm Ublox NEO 7M GPS Capture sensitivity : 148 dBm Ublox NEO 7M GPS cold start time:...
Reference: RBD-0959
KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Reference: RBD-0735
Pixhawk PX4 2.4.8 Drone Flight Controller Autopilot Kit
Supply Voltage: 7V.Processor: 32 Bit Cortex M4 CoreBus interface (UART, I2C, SPI, CAN).Firmware: Mission planner.Sensors: Gyrometer, Accelerometer, Barometer & MagnetometerMicro SD card to record flight data. RoboticsBD
Reference: RBD-0237
APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: RBD-0938
Mini OSD Module for APM PIX Pixhawk Pixhack Flight Control Board
ATmega328P with Arduino bootloader MAX7456 monochrome on-screen display FTDI cable compatible pinout Standard 6 pin ISP header 2 independent power sections with an LED indicator on each Solder jumpers for combining the power sections
Reference: RBD-0821
UBLOX NEO-7M NEO 7M GPS w/ Compass Stand Holder for APM ArduPilot Mega 2.6 Pixhawk Flight Control
UBLOX NEO-7M Tracking sensitivity: 161 dBm UBLOX NEO-7M Capture sensitivity : 148 dBm UBLOX NEO-7M cold start time: 38s average UBLOX NEO-7M Warm start time: 35s average UBLOX NEO-7M hot start time: 1s average UBLOX NEO-7M Capture time: 0.1s Average Compass Stand Holder Material: CNC Aluminum alloy, carbon glass fiber rod Compass Stand Holder Mounting rod...
Reference: RBD-0704
CC3D Flight Controller OpenPilot STM32 32-bit Flexiport
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-0228
APM Shock Vibration Absorber
Color: Black Material: Glass-fiber Suit for different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4 Package Weight: 24 gm.
Reference: RBD-0288
GY-801 - Multi Sensor Board
Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v
Reference: RBD-0729
GPS Antenna 1575.42 MHz SMA Male 3 Meter
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0946
Generic SP Racing F3 EVO Brushed V2.0
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-1546
APM 2.8 Flight Controller + NEO GPS M8N
Model: APM 2.8 APM 2.8 Flight Controller Input Voltage (V): 12-16 V. APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 NEO-M8N GPS Module Dimensions: Outer diameter 54mm NEO-M8N GPS Module Ready to Connect to All APM FC with 5-pin connector Attached NEO-M8N GPS Module Receiver...
Reference: RBD-1722
NEO-M8N GPS Module with Ceramic Active Antenna
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.