

This is Dot Led Matrix Module incorporating MAX7219 Driver chip. By using this dot LED module in your upcoming project, you will be able to add some great cool animation. RoboticsBD
The individual module features 8×8 LED’s, each controlled very precisely by the MAX7219 driver to generate the color pattern you wish. The great advantage of using this is users will have control over all of the 64 LED by just connecting 3 output communication wires to microcontrollers like Arduino etc. RoboticsBD
Connecting the two modules is also very easy. Only connect the output pins of the previous breakout board to the input pins of the new module, thus with such arrangement, you can connect as many DOT LED Modules to the Arduino
The MAX7219 Dot Led Matrix Module is a serial input common-cathode driver that interfaces micro-controllers to LED matrices. All common micro-controllers can be connected to this module by using a 4-wire serial interface. Each output can be addressed without refreshing the entire display. This module requires only 3 I/O lines for driving the display, making it ideal for your microcontroller projects. Only one external register is used to set the segment current of each LED. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Dot LED Module to the Arduino
Vcc – 5V
GND – GND
DIN – Pin 12
CS – Pin 10
CLK – Pin 11
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Driver IC | MAX7219 |
Input Voltage (V) | 5 |
Max. Operating Current (mA) | 320 |
LED Color | Red |
Length (mm) | 32 |
Width (mm) | 32 |
Height (mm) | 6 |
PCB Size ( L x W ) mm | 50 x 32 |
Weight (gm) | 20 |
Shipment Weight | 0.022 kg |
Shipment Dimensions | 7 × 5 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x MAX7219 Dot Led Matrix LED Display Module.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of MAX7219 Dot Led Matrix LED Display Module in Bangladesh is BDT 250 You can buy the MAX7219 Dot Led Matrix LED Display Module at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0914
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
Reference: RBD-1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-2091
Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-0028
Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-2218
Module package (with FLASH memory and peripheral circuits) have DIP16, DIP28, chip packaging has DIP18, SSOP20, and LQFP32 form. Built 13Bit/DA converter, and 12Bit/PWM output. PWM output can directly drive 0.5W/8Ω speakers, push-pull current abundant support DAC / PWM output of two ways. Support for loading WAV audio formats. USB download mode, support...
Reference: RBD-1219
Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage Easy to expand the experiment with SD card...
Reference: RBD-0937
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
Reference: RBD-2095
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...
Reference: RBD-1331
High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-2226
Operating Voltage: 24V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...
Reference: RBD-1400
4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-2089
Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected.
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-1973
Brand: DFRobot
Easy-to-use Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces
Reference: RBD-0108
Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1840
The DS1302 trickle-charge timekeeping chip module with battery backup A real-time clock/calendar and 31 bytes of static RAM. Communicates with a microprocessor via a simple serial interface. Real-time clock/calendar provides seconds, minutes, hours, day, date, month, and year information. Note: Batteries not included.
Reference: RBD-2230
Main chip: NE555 Input Voltage: 5V-15V DC. Generate an adjustable pulse for MCU. Generate an adjustable pulse, to control circuitry associated.
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-1941
Length: 20cm Cable size: 26AWG. Solid and durable. Safe and easy to install. RoHS compliant.
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1822
Input interface: Type C Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-2022
Current Rating: 3A Voltage Rating: 250V Connector Type: Header JST-XH 3 Pin Connector
Reference: RBD-2093
This is a High-quality photosensitive sensor module/light module detects the photosensitive resistor for Arduino Resistance of the photoresistor is typically less than 80 Ohms (in full light) Dark resistance is typically greater than 20 Meg Ohms (in full darkness)
Reference: RBD-1430
Double Pole Double Throw. Main Body: 12 x 12 x 10mm. Lever Length: 11mm.
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.