Reference: RBD-0665

Rain & Steam Detection Sensor Module

Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation

Reference: RBD-0830

Thermocouples - K Type 800C WRN-291 200mm Rod

Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree.  Screw Type

Reference: RBD-2099

Touch Sensor Switch Module

Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins

Reference: RBD-2079

38KHz Infrared Transmit Sensor Module

This is 38KHz Infrared IR transmitter sensor module For Arduino Transmit 38KHz modulating signal Suitable for Arduino DIY project Material: PCB

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0687

BMP280 Pressure Sensor Module

Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V. Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C). Peak current: 1.12mA. RoboticsBD Operating Pressure: 300 hPa to 1100 hPa. Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.

Reference: RBD-0152

SW-420 NC Type Vibration Sensor Module

Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation

Reference: RBD-1918

Miniature Vibrating Motor 6x15

Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V

Reference: RBD-1640

12V Gas Detector Sensor Alarm Propane Butane LPG Natural

Color: White Material: Metal + Plastic Operating Voltage : 12V DC Standby Current : ≤90mA Alarm Current : ≤100mA

Reference: RBD-0672

MQ-3 Alcohol Gas Sensor

Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output:  0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.

Reference: RBD-2125

QRE1113 Reflective Optical Sensor

Phototransistor output  No contact surface sensing  Miniature package

Reference: RBD-1672

Tuya PIR Motion Sensor for Smart Life Wifi Based Alarm System

Model Number: P06 Product Name: PIR Sensor Indoor Communication: greater than 20 Meters Detect Angle Side View: 128 degrees Detect Angle Down View: 128 degrees Detect distance: 10 Meters<

Reference: RBD-1210

OPT101P PHOTODIODE/AMPLIFIER

Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz

Reference: RBD-1018

Weighing Load Cell Sensor 5kg

Dimensions: 75 x 13 x 13 mm (L x W x H) Range: 5 kg Cable Length: 18 cm Fitting ScrewHole Size:  M3 Rated output: 1.0 0.1mV / V Nonlinear: 0.05% F.S Hysteresis: 0.0% F.S Repeatability: 0.05% F.S

Reference: RBD-0132

TCRT5000L Reflective Optical Sensor

The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...

Reference: RBD-0572

VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB W/ I2C Interface Arduino

Operating Power: 60mW/15fpsVGAYUV. Sleeping Mode: <20 uA. Lens Size: 1/6″. Max. Frame Rate: 30fps VGA. Sensitivity: 1.3V / (Lux-sec). dynamic range: 52 dB. Electronic Exposure: 1 to 510 row.

Reference: RBD-1935

Water Level Sensor Gold Coating

Water-level sensor indicates the level of water in an overhead tank Gold coated Long life time Simple working procedure

Reference: RBD-2172

Force Sensitive Resistor Square 40mm

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD Force Sensitive Resistor Square High Quality

Reference: RBD-0425

GY-9960LLC APDS-9960 RGB and Gesture Sensor Module

Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD

Reference: RBD-2170

100mm x 100mm Medium Magnetic Field Viewing Paper

Visualize magnetic fields with ease using the field paper Large size of 100mm x 100mm for a clear and detailed view Micro-encapsulated film enables visualization of magnetic fields Suitable for use with any magnet Lightweight and compact for easy handling and storage

Reference: RBD-0430

Line Follower Sensor- 8 Array

Operating voltage: 4.5V to 5.0 V Output format: 8 Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD

Reference: RBD-2169

US1000-21A Integrated Ultrasonic Underwater Sensor

US1000-21A ultrasonic flow sensor  ultrasonic heat meter sensor  Underwater Sensor  high-frequency ultrasonic sensor Model: US1000-21A High frequency type ultrasonic underwater sensor Transceiver category Nominal frequency: 1.0MHz ± 5% Bandwidth: 200.0KHz

Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-0429

BH1750FVI Digital Light intensity Sensor

High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface

Reference: RBD-1365

Uni-T UTi85H+ Professional Thermal Imager

Central point temperature measurement high/low temperature auto tracking real-time temperature display  Alarm buzzer: >37.2ºC: high temperature audible alarm

Reference: RBD-1719

Envitec OOM202 Medical Ventilator Oxygen Sensor

Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December

Reference: RBD-0352

Knock Sensor Module KY-031

Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD

Reference: RBD-1208

Laser Receiving Sensor

Working Voltage: 5V DC Operating Temperature: -30ºc ~ 85ºc Output high level when received the laser signal Output low level when not receive laser signal. Application: Electronic Circuits

Reference: RBD-0693

Infrared Line Track Tracker Follower Sensor

Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...