How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
The AM2315C is a nice, enclosed temperature and humidity sensor from the same folks that brought us the AM2315. In fact, this enclosed sensor looks an awful lot like the popular AM2315 temperature and humidity sensors, but inside is the AHT20.
You can power it with anything from 2.5V to 5.5V so it's good with 3V or 5V microcontrollers. You can take sensor readings as often as you like, and it uses standard I2C so it's super easy to use with any Arduino or Linux/Raspberry Pi board.Whew, that makes things a little easier, doesn't it?
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
The AM2315C is a nice, enclosed temperature and humidity sensor from the same folks that brought us the AM2315. In fact, this enclosed sensor looks an awful lot like the popular AM2315 temperature and humidity sensors, but inside is the AHT20.
You can power it with anything from 2.5V to 5.5V so it's good with 3V or 5V microcontrollers. You can take sensor readings as often as you like, and it uses standard I2C so it's super easy to use with any Arduino or Linux/Raspberry Pi board.Whew, that makes things a little easier, doesn't it?
While it is not rated as 'weatherproof', this sensor would do much better for sensing where there might be wind, rain, zombies, etc. than SHT PCB-breakout sensors, and the I2C interface makes it easier to interface with microcomputers that can't do the delicate timing of DHT sensors.
This sensor has a typical accuracy of ±2% relative humidity, and ±0.3 °C at 20-80% RH and 20-60 °C. There is only one I2C address so it's not a good option when you need multiple humidity sensors.
That said, for maker and IoT projects? You can't beat the simplicity and price! And we've got ready-to-go working Arduino and CircuitPython code to use it. Check out our detailed guide for library code, datasheet, and more
Each order comes with one AM2315C sensor with built-in pullups. You just provide any microcontroller that can run our Arduino or CircuitPython library.
The latest price of AM2315C Encased I2C Temperature/Humidity Sensor in Bangladesh is BDT 1,750 You can buy the AM2315C Encased I2C Temperature/Humidity Sensor at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-2841
The Humidity Sensor SYH-2R is an analog air humidity sensor designed to accurately measure humidity levels by changing resistance in response to varying humidity conditions. Operating within a wide range from 10% to 95% relative humidity (RH), this sensor provides reliable data on ambient moisture levels. The sensor module comes without a case, offering...
Reference: RBD-3300
The SHT35 Temperature and Humidity Sensor Module is a high-precision and high-performance digital sensor designed for accurate environmental monitoring. It features I2C communication for easy interfacing with microcontrollers like Arduino, ESP32, STM32, and Raspberry Pi.
Reference: RBD-0147
Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-1654
5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector Color Black
Reference: RBD-2056
Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5sSize: 4*30*500mmRange: -50C ~ 200C
Reference: RBD-0424
SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface
Reference: RBD-2217
Based on the semiconductor LM35 temperature sensor Can be used to detect ambient air temperature Calibrated directly in °Celsius (Centigrade) Linear + 10 mV/°C Scale Factor 0.5°C Ensure accuracy (at +25°C) Low power consumption, less than 60uA Low output impedance, 1mA current through only 0.1Ω With screw holes for easy installation and fixed. Aperture...
Reference: RBD-0923
Measuring range: temperature -40-80 ℃; humidity 0; 99.9%RH Measurement accuracy (25℃): temperature: + 0.5; humidity: + 2%RH (10; 90%RH) Resolution: temperature: 0.1 ℃, humidity: 0.1%RH Attenuation value: temperature: <1℃ / year; humidity: < 1%RH/ years High precision Capacitive type Full range temperature compensated Relative humidity and...
Reference: RBD-2482
Module utilizes the popular 1-Wire DS18B20 temperature measurement IC.
Reference: RBD-2654
The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.
Reference: RBD-1946
Comes with the BME280 sensor. Pressure accuracy of ±1 hPa. Temperature accuracy ±1.0°C. Altimeter accuracy ±1 meter. Humidity: +-3%
Reference: RBD-2845
Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-2343
AHT10 High Precision Digital Temperature and Humidity Sensor Module I2C interface for easy integration with microcontrollers Wide operating voltage range: 1.8V to 6.0V High accuracy: ±0.3°C for temperature, ±2% for humidity Compact size: 4x5mm with a height of 1.6mm, ideal for space-constrained projects Provides calibrated digital output with excellent...
Reference: RBD-2846
The DHT-11 Digital Temperature and Humidity Sensor is a compact and reliable sensor that can measure temperature and humidity with high accuracy. This sensor features a single-wire interface, making it easy to integrate with microcontrollers and other electronics projects. The DHT-11 has a temperature measurement range of 0°C to 50°C with an accuracy of...
Reference: RBD-2806
K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃
Reference: RBD-3587
This compact and powerful module combines the ESP8266 ESP-01/ESP-01S WiFi microcontroller interface with the reliable DHT11 temperature and humidity sensor, offering a seamless solution for real-time environmental monitoring in IoT and smart home applications. Designed for users who prefer customization and development flexibility, this module allows you...
Reference: RBD-0414
A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...
Reference: RBD-2555
This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level. Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...
Reference: RBD-2745
The LSM9DS1 is a versatile, motion-sensing system-in-a-chip. It houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer – nine degrees of freedom (9DOF) in a single IC! The LSM9DS1 is equipped with a digital interface, but even that is flexible: it supports both I2C and SPI, so you’ll be hard-pressed to find a microcontroller it doesn’t...
Reference: RBD-0665
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-2380
High Precision Measurement: Digital temperature and humidity sensor with integrated sensing capabilities. Low Power Consumption: Operates efficiently with very low power, ideal for battery-powered applications. Factory Calibrated Sensors: Ensures excellent accuracy and reliability in measurements. Wide Supply Voltage Range: Operates between 2.7V to 5.5V,...
Reference: RBD-1671
ESP32 Bluetooth Wi-Fi development board, support NodeMCU / Arduino DHT11 temperature and humidity sensor CP2104 communication chip USB TO TTL Micro USB port Soil probe (long) soil temperature and humidity detection module 18650 Lithium Battery Holder Powered (Battery is not included)
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-2169
US1000-21A ultrasonic flow sensor ultrasonic heat meter sensor Underwater Sensor high-frequency ultrasonic sensor Model: US1000-21A High frequency type ultrasonic underwater sensor Transceiver category Nominal frequency: 1.0MHz ± 5% Bandwidth: 200.0KHz
Reference: RBD-1179
Temperature measuring range: 0...100°C Typical Input Voltage:3.3VDC,5VDC Operating Current:60uA Interface: Analog ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase unless you're confident that you can use it successfully.
Reference: RBD-2249
Made From High-Quality Materials. Electronic High-Frequency Oscillations (2.4MHz). Material: Ceramic, Wire Diameter: Atomizer: 1.58cm/0.62in; Sealing ring: 2.0cm/0.75in
Reference: RBD-1384
OUT OF STOCK Try Alternative Product Wide Temperature range: -50~+420°C or -58~788°F High accuracy of ±1.5% or ±1.5°C Whichever is greater Distance Spot Ratio of 12:1 °C/°F Selection Auto Data Hold Laser Target Pointer ON/OFF selection Backlight ON/OFF selection Auto Power Off if idle or no operation in 7sec Large LCD Screen w/ easy to read Instant...
Reference: RBD-3294
Sensor Model: BMP280 Operating Voltage: 5V DC Interface: I2C (Standard) / SPI (Optional) Temperature Range: -40°C to +85°C Temperature Accuracy: ±1°C
Reference: RBD-0654
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount. RoboticsBD
Reference: RBD-0942
Manufacturer: AMASS Type of connector: DC supply Connector series: XT60H Kind of connector: Female Number of pins: 2
Reference: RBD-1655
Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 4A. Load regulation (%): ±5. Input Plug: 2-Pin US type. Output Plug: DC Jack 5.5mm.
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0656
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount.
Reference: RBD-0754
Plug Type: 5.5 x 2.1mm Pin: 3 Temperature: -30°C ~ +70°C. Rated load: up to DC 30V / 1.0A. Contact resistance: ≤0.03. Insulation resistance: ≥100 MΩ.
Reference: RBD-2639
Connect components on breadboards and PCBs easily.20 pre-crimped jumper wires for versatile use.20cm length for convenient connections.Male-to-male connector design for simple use.Colorful for easy identification and organization.
Reference: RBD-3485
The VEML7700 Ambient Light Sensor Module is a high-precision light measuring solution designed for applications requiring accurate ambient light detection. Built around the advanced VEML7700 sensor, this module can detect illumination levels ranging from 0 to 120,000 lux with 16-bit resolution, making it ideal for smart lighting systems, automatic screen...
Reference: 1730
Through-hole design. Shaft Shape: Round Base Size (mm): 6mm and 7mm Middle stroke 1.05mm and 2mm Shaft Size: 10 different Size (find the details in Package Includes section below) Please Choose Size Below:
Reference: RBD-3212
The STM32 Starter Kit B is a comprehensive development kit designed for beginners and professionals to explore the STM32 ecosystem. Equipped with an STM32F103C8T6 microcontroller, this kit combines a development board, an STM32Block expansion board, and a breadboard for hands-on learning. Featuring onboard input/output modules, sensors, and LED circuits,...
Reference: RBD-1817
USB Plug and Play. RFID reader 0-8cm Reading Distance. Win8/7/XP/Android Supported. S50/S70 Card Supported. OTG Phone Connection. Built-in buzzer and LED for identification.
Reference: RBD-3108
The DC5.5V-35V Positive Negative Voltage Stabilizing Power Supply Module is the ultimate solution for your voltage regulation needs. This compact and efficient module boasts low ripple and linear adjustable stabilizing voltage regulation, making it ideal for a wide range of applications, from DIY projects to professional setups.
Reference: RBD-3130
The WeAct STM32H723VGT6 Core Board is a high-performance development platform designed around the STM32H723 microcontroller, part of the STM32H7 series. With a powerful ARM Cortex-M7 core running at up to 550MHz, it is ideal for advanced embedded projects requiring robust processing, graphics, and data handling. This board includes features such as a TFT...
Reference: RBD-3410
Brand: Sonoff
Compact Design: Fits standard recessed boxes. WiFi Control: Manage devices via app. Scheduling: Automate on/off times. Voice Activation: Compatible with Alexa and Google Assistant. Real-Time Monitoring: Check device status in the app. Easy Installation: Plug-and-play; keeps existing switch functionality.
Reference: RBD-1145
Version 1.4 HDMI to micro HDMI cable Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution Cable Length: 1.5m Color: Black Application: Mulitimedia
Reference: RBD-2688
Assortment of 75 plastic gears for building and customizing gearboxes in robots, models, toys, and more. Includes various gear types like spur gears, crown gears, worm gears, and pulleys. Offers a wide range of sizes to meet diverse project requirements. Ideal for beginners and hobbyists for creating gear-driven mechanisms.
The AM2315C is a nice, enclosed temperature and humidity sensor from the same folks that brought us the AM2315. In fact, this enclosed sensor looks an awful lot like the popular AM2315 temperature and humidity sensors, but inside is the AHT20.
You can power it with anything from 2.5V to 5.5V so it's good with 3V or 5V microcontrollers. You can take sensor readings as often as you like, and it uses standard I2C so it's super easy to use with any Arduino or Linux/Raspberry Pi board.Whew, that makes things a little easier, doesn't it?
