Reference: RBD-2081

Mini Dry Reed Pipe Module

Operating Voltage: 3.3V to 5v Output Type: Digital

Reference: RBD-1810

L293D Shield for NodeMCU V2

Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver

Reference: RBD-0702

1 Channel 5V Relay Board Module

It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock

Reference: RBD-0985

Xbee Shield For Arduino V03

Stackable design, easy to plug into the ARDUINO development board. Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly. 3.3v and 5v dual power output. 3.3v and 5v IO compatible. USB2.0 protocol.

Reference: RBD-2220

Full Color LED Module SCM Light Water 5050 LED Module For Arduino

Good PRINT PACK design, very beautiful. 8 world of the three primary colors (red-green-blue) LED color, scanning control mode. Applicable for various platforms, such as 51 / AVR / AVR / ARM / for Arduino All kinds of platforms.

Reference: RBD-1575

5V 2 Channel Solid State Relay (SSR)

Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac

Reference: RBD-2242

LilyPad SMD LED Yellow Color

Wearable e-textile technology.  Designed with large sew tabs LED Yellow Color

Reference: RBD-2228

CJMCU-9833 AD9833BRMZ Programmable Sine Triangular Square Waveform Generator Module

Working voltage: 2.3V-5.5V. Working temperature range: -40 ~ + 105. Onboard 25MHZ (accuracy of 50ppm) active crystal. On-board high-speed amplifiers

Reference: RBD-0987

Arduino NANO I/O Extension Shield

Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.

Reference: RBD-0737

5V 1 Channel Solid State Relay (SSR)

Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac

Reference: RBD-1164

LCD Display 16X2 with Header

For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.

Reference: RBD-2209

Servo Motor Controller Driver Board 16 Channels High Accuracy MCU Software

16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms

Reference: RBD-1417

MAX7219 Dot Led Matrix LED Display Module

SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red

Reference: RBD-2087

Photo Interrupter Module

Voltage 5V Photo interruption module triggers a signal when light is blocked between the opening of the sensor.

Reference: RBD-1842

Stainless Steel 1m Conductive Thread Wire for Wearable Lilypad

Material: 12UM Stainless steel fiber Gram Weight: 0.2458g/m Strength: 2.8KGF. Length: 1m. Diameter(mm): 0.12. Resistance (Ω/m) : 27.

Reference: RBD-0990

XFS5152CE Speech Synthesis Module TTS Voice Module

Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.

Reference: RBD-2149

50kg Half-bridge Experiments Body Scale Load Cell Sensor

Capacity (Kg): 50. Output Sensitivity (mv/v): 1.0±0.1. Nonlinearity (%FS): 0.03. Repeatability (%FS): 0.03. Input Resistance (Ω): 1000. Insulation Resistance (MΩ): ≥5000.

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-2240

LilyPad SMD LED Green Color

Wearable e-textile technology.  Designed with large sew tabs LED Green Color

Reference: RBD-0699

1.8" inch TFT LCD Display module ST7735S 128x160

Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI

Reference: RBD-1332

I2C Graphic 128x64 LCD Adapter

Adapter: Graphic 128x64 Communication: i2c 

Reference: RBD-2156

4×4 Matrix 16 Keyboard Keypad

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.

Reference: RBD-2216

PCF8591 Module Analog to Digital / Digital-Analog Converter Module

Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...

Reference: RBD-1773

VHM-314 V3.0 Bluetooth Audio Receiver Board

Supply Voltage: 5V USB / 3.7V lithium battery Output Port: 3-wire audio interface/DIY pad Output Type: Analog signal Bluetooth name: VHM-314-V3.0 Bluetooth version: 5.0 Bluetooth passcode: no password Sound source: Bluetooth. USB-PC input(after the back pad is connected, the computer can be connected as a sound card though Micro) Operation method:...

Reference: RBD-1138

AI-thinker A9G GSM/GPRS+GPS/BDS Development Board

Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-1762

Mini BD243 Bubble 9-12V Tesla Coil Electronics Wireless PCB Module

Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm):  3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.

Reference: RBD-0348

Heart Rate Pulse Sensor Module For Arduino

A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....