

A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and instead use the recommended cable available here: High-Quality USB Cable.
The core of this module is the ESP32 chip, which is scalable and adaptive. Two CPU cores can be individually controlled. The clock frequency is adjustable from 80 MHz to 240 MHz and supports RTOS. RoboticsBD
It is a general-purpose Wi-Fi+BT+BLE MCU module.ESP-WROOM-32s The module integrates traditional Bluetooth, Bluetooth low energy and Wi-Fi. Wide range of uses: Wi-Fi supports a wide range of communication connections, as well as a direct connection to the Internet via a router; Bluetooth allows users to connect to a mobile phone or broadcast a BLE Beacon for signal detection. RoboticsBD
The module supports data rates up to 150 Mbps and antenna output power of 20dBm for maximum wireless communication. As a result, this module has industry-leading specifications and performs well in terms of high integration, wireless transmission distance, power consumption, and network connectivity Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Module model | ESP-WROOM-32s |
SPI Flash | 32Mbit(default) |
Support interface | UART/GPIO/ADC/DAC/SDIO/SD card /PWM/I2C/I2S |
Integrated crystal oscillator | 40MHz Crystal oscillator |
IO Port | 38 |
Antenna | Onboard antenna |
Power Supply | Voltage 3.0V ~ 3.6V,Typical 3.3V,Current >500mA |
Operating Temperature | -40 ℃ ~ 85 ℃ |
Storage Environment | -40 ℃ ~ 120 ℃ |
Length(mm) | 25.4 |
Width(mm) | 48.26 |
Height(mm) | 3 |
Weight(g) | 10 |
Shipment Weight | 0.015 kg |
Shipment Dimensions | 12 × 8 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi
The latest price of ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi in Bangladesh is BDT 740 You can buy the ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please...
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-1558
TTGO Meshtastic T-Beam V1.1 ESP32 915Mhz or 433Mhz (Ships Random) WiFi Bluetooth ESP32 GPS NEO-6M SMA 18650 Battery Holder OLED (915Mhz OLED)
Reference: RBD-1671
ESP32 Bluetooth Wi-Fi development board, support NodeMCU / Arduino DHT11 temperature and humidity sensor CP2104 communication chip USB TO TTL Micro USB port Soil probe (long) soil temperature and humidity detection module 18650 Lithium Battery Holder Powered (Battery is not included)
Reference: RBD-1765
LILYGO TTGO Model: 915MHZ CH9102F T3_V1.6.1 LoRa32 V2.1_1.6 Version 915Mhz ESP32 LoRa OLED 0.96 Inch SD Card Bluetooth WIFI Wireless Module ESP-32 SMA
Reference: RBD-1806
Based on ESP32 240MHz Xtensa dual-core 32-bit microprocessor Operating Voltage: 2.7V – 4.2V Working Current: 60mA Battery Charging Current: 500mA
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-2240
Wearable e-textile technology. Designed with large sew tabs LED Green Color
Reference: RBD-0136
Microcontroller: AT91SAM3X8E Operating Voltage: 3.3V Input Voltage (recommended): 7-12V Input Voltage (limits): 6-16V Digital I/O Pins: 54 (of which 12 provide PWM output) Analog Input Pins: 12 Analog Outputs Pins: 2 (DAC) A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. CPU clock at 84Mhz 96KBytes of SRAM
Reference: RBD-2131
ESP32-S2 based WIFI development board Features S2FN4R2 WIFI IC Equipped with 4MB FLASH and 2MB PSRAM Type-C USB connectivity 27 digital input/output pins with support for interrupt/pwm/I2C/single wire ADC, DAC, I2C, SPI, UART, USB OTG
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-1214
The board is compatible with Mega 2560. excellent solution for developing projects based on ATmega2560. The board can be powered directly through the Micro USB connector The maximum output current upon 5V is around 800mA, while on the 3.3V it is about 800mA.
Reference: RBD-0106
Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language.
Reference: RBD-0154
Microcontroller: ATmega32u4 Operating Voltage: 5V Input Voltage (Recommended): 7-12V Input Voltage (limits): 6-20V Digital I/O Pins: 20 PWM Channels: 7 Analog Input Channels: 12
Reference: RBD-0576
Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD
Reference: RBD-2164
WeMos D1 R32 Mini ESP32 WIFI Bluetooth Development Board CH340 chip for compatibility with Arduino UNO R3 Supports WIFI and Bluetooth connectivity Comes with a Type-B/Micro USB adapter
Reference: RBD-2053
ATMEGA32U4 running in 5V / 16MHz Support Arduino IDE V1.0.1 Micro USB interface programming on the board Four 10-bit ADC pin 12 digital I / O (5 PWM capability) Rx and Tx hardware serial connection. RoboticsBD
Reference: RBD-1827
Altera Cyclone IV EP4CE6 FPGA Development Board NIOSII EP4CE PCB USB Blaster Jtag AS Programmer
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-2238
Wearable e-textile technology. Designed with large sew tabs LED Blue Color
Reference: RBD-1602
Microcontroller: ESP8266EX Operating Voltage: 3.3V Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0) Analog Input Pins: 1 Flash Memory: 4MB On-Board Switching Power Supply: Input Voltage Range: 9V to 12V Output: 5V at 1A Max
Reference: RBD-1216
14-/20-pin DIP (N) Socket 20 pin LaunchPad standard leveraging the BoosterPack ecosystem On-Board EZ-FET emulator featuring EnergyTrace™ technology Supports MSP430G2xx2, MSP430G2xx3, and MSP430F20xx devices in PDIP14 or PDIP20 packages 1 user buttons and 3 LEDs for user interaction
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-1541
For beginners who are interested in Arduino A complete set of Arduino’s most common and useful electronic components Infrared sensor receiving module Laser sensor module Temperature and humidity sensor module Infrared sensor module 5v relay module Obstacle avoidance sensor module.
Reference: RBD-1761
USB Type: Type-A to Type-B Weight: 80 gm. Length: 1m / 3.2Feet Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-1133
Compatible with NUCLEO-F411RE, onboard Cortex-M4 microcontroller STM32F411RET6 Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion Supports mbed, build prototype quickly by mbed SDK and online tools...
Reference: RBD-1603
USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-2243
Wearable e-textile technology. Designed with large sew tabs Button Board
Reference: RBD-2267
Integrated Wi-Fi and Bluetooth connectivity make this board a great choice for IoT projects and robotics. The ESP32 chip on the board is a dual-core microcontroller that operates at up to 240 MHz, providing ample processing power for complex projects. With 520 KB of SRAM and 4 MB of flash memory, the board has plenty of memory for storing and running...
Reference: RBD-0926
USB Driver: FT232 Manufacturer: Gravitech Operating Voltage (logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please...
Reference: RBD-1809
Digispark Pro ATtiny167 Micro USB 16MHz
Reference: RBD-2126
Manufacturer: China Support TWI and SPI communication Input voltage (recommended) range from 7V to 12V Input Voltage (limit) range from 6V to 20V 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs) Onboard ATmega32u4 microcontroller with 32KB flash memory, 2.5KB SRAM and 1KB EEPROM
Reference: RBD-2244
Wearable e-textile technology. Designed with large sew tabs Slide Switch
Reference: RBD-1527
Based on ATmega32 8 Bit microcontroller USB external programmer Included Datasheet, Manual, Software & Sample codes All Port pins pins available for peripheral interfacing
Reference: RBD-0838
ATMEGA32U4 running in 5V / 16MHz Support Arduino IDE V1.0.1 Micro USB interface programming on the board Four 10-bit ADC pin 12 digital I / O (5 PWM capability) Rx and Tx hardware serial connection. RoboticsBD
Reference: RBD-0763
Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-1634
Size: 0.91 inch Resolution: 128 x 32 Controlling Chip: SSD1306 Display Area: 22.384 x 5.584mm Driving Voltage: 3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-0555
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Reference: RBD-1976
High sensitivity for Low-Light Operation. Low Operating Voltage for Embedded Portable Apps. Supports Scaling. The Standard SCCB Interface is Compatible with the I2C Interface.
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-1159
Removes all Solder Residue Low cost and high-quality Ideal replacement for the old sponges. Removes excess solders from soldering iron tips Provides extended tip life