Reference: RBD-0658

FTDI USB to TTL Serial Converter Adapter FT232RL

Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...

Reference: RBD-0176

Brand: SparkFun Electronics

Rover 5 Robot Platform 4 Motors 4 Encoders

Arduino Compatible Easy to assemble Adjustable gear box angles 4 independent DC motors 4 independent hall-effect encoders Thick rubber tank treads 10Kg/cm stall torque per motor

Reference: RBD-2261

7mm Motor Shaft Coupling Brass Hex 18mm length

Type: Hexagonal coupling. Material: brass. Inner diameter: 7 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm

Reference: RBD-100

Robotic Claw - MKII With Metal Servo

Description: This robotic claw is a step up from the classic. The MKII takes everything you loved about the standard robot claw from DAGU and makes some significant improvements! 

Reference: RBD-1354

Jumper Wire Single Medium

Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.

Reference: RBD-1709

6mm Hex coupling for Robot Smart Car Wheel 30mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm

Reference: RBD-0350

STM32F103C8T6 Blue Pill Development Board

100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.

Reference: RBD-1893

18650 Lithium Battery Charger USB Micro-B

Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-1559

DC 12V Charging Step Up Booster Module for 18650 Lithium Battery UPS Voltage Converter Protection

Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection

Reference: RBD-0415

801S Vibration Sensor Module

Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-0237

APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW

Description: This Telemetry radio set allows you to link to  a flight controller such as the APM or Multiwii  AIO via a USB equipped device such as a  computer, laptop or tablet supporting a USB  connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-1334

TP4056 Li-Ion Battery Charger with Protection

Charging current: 1A (maximum) Maximum charging voltage: 4.2V (1.5% accuracy) Input voltage: 4.5V-5.5V

Reference: RBD-0032

Arduino Nano V3.0 (CH340)

Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch.

Reference: RBD-2258

85mm Antiskid Wheel (Pack of 4)

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Black Tire + Blue Rim If you need to purchase single 85mm Wheel. Vist here. Note: Hex coupling not...

Reference: RBD-0288

GY-801 - Multi Sensor Board

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-0103

NRF24L01+ 2.4GHz Wireless Transceiver Module

Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch...

Reference: RBD-0440

433Mhz Wireless Serial Transceiver Module - 1 Kilometer

433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD

Reference: RBD-258

Brand: SparkFun Electronics

SparkFun Micro OLED Breakout

SparkFun Micro OLED Breakout

Reference: RBD-1187

Line Follower Robot Kit

Operating Voltage: 5V Easy to install Comes with Stepwise User manual

Reference: RBD-0749

85mm Antiskid Shockproof Wheels High Quality

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim

Reference: RBD-1537

EL Wire-White 3m With Pocket Inverter

Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: White

Reference: RBD-1070

Ball Caster 3PI N20

Dimensions: 22 x 15 mm (Diameter x Height) Weight: 10 gm Body Case Material: Plastic Ball Material: 304 Stainless Steel Application: for MiniQ robot

Reference: RBD-2074

5v Relay module for Arduino

Output SPDT Relay. Header connector for connecting power and trigger voltage. Screw terminal connector for easy relay output connection. Note: Relay might be different from the picture as per stock

Reference: RBD-0566

RS485 USB-485 Converter Adapter Support Win7 XP Vista Linux Mac OS

Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM

Reference: RBD-0393

JoyStick 5Pin Breakout Module For Arduino

Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD

Reference: RBD-1949

DC12V N20 Gear Motor 300 RPM & Mount Bracket & 43mm Wheel

N20 Micro Gear 12V 300RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel

Reference: RBD-0691

IR Infrared Remote Decoder Encoding Transmitter & Receiver Wireless Module

Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters