- Reduced price

Note: The component, colour & shape of the motor may vary depending on our stock rotation.
Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
This servo motor requires a higher current and cannot be powered directly from the Arduino Uno or Mega. You will need to provide an additional 5V, 3A power supply in conjunction with the Arduino. |
RED – Positive
Brown – Negative
Orange – Signal
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Model | MG90S |
Weight(gm) | 13 |
Operating Voltage (VDC) | 4.8 ~ 6.6 |
Operating Speed @4.8V | 0.10sec/60° |
Operating Speed @6.6V | 0.08sec/60° |
Stall Torque @ 4.8V (Kg-Cm) | 1.8 |
Stall Torque @6.6V (Kg-Cm) | 2.2 |
Operating Temperature (°C) | 0 to 55 |
Dead Band Width ( μs) | 1 |
Rotational Degree | 180º |
Servo Plug | JR |
Cable Length (cm) | 25 |
Length (mm) | 12.4 |
Width (mm) | 22.8 |
Height (mm) | 32.5 |
Shipment Weight | 0.017 kg |
Shipment Dimensions | 8 × 6 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Towerpro MG90S Mini Digital 180 Degree Servo
Set of Horns
1 x Set of Screws.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Servo Motor Micro MG90S 180 Degree Rotation in Bangladesh is BDT 250 You can buy the Servo Motor Micro MG90S 180 Degree Rotation at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0295
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 9.4kg-cm Stall torque @6.6V : 11kg-cm Continuous rotation servos are like regular hobby RC servos but modified to offer speed control instead of position control. They're essentially compact, affordable motors with integrated motor drivers. Add a wheel, and...
Reference: RBD-0297
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-1346
Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm
Reference: RBD-0563
Overcharging and Over Discharging Protection Short circuit protection: Yes Applicable assembly: Nominal 4.5V Batteries / 3 strings. RoboticsBD
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0235
Brand: SparkFun Electronics
Description: This is a framed graphical LCD 64x128 with LED backlight. This unit is a very clear STN type LCD with a simple command interface. This new module includes the negative voltage circuitry on board!
Reference: RBD-0355
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
Reference: RBD-1301
Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high
Reference: RBD-0102
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Reference: RBD-0032
USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-0358
Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-0653
Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)
Reference: RBD-0395
Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function. RoboticsBD
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0108
Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...
Reference: RBD-2258
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Black Tire + Blue Rim If you need to purchase single 85mm Wheel. Vist here. Note: Hex coupling not...
Reference: RBD-2261
Type: Hexagonal coupling. Material: brass. Inner diameter: 7 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: RBD-0829
Material: Aluminium M3 Screws Adjustable type servo arm Mounting Hole Spacing: 14mm Servo disc diameter: 20mm 25Tooth Weight: 2 gm
Reference: RBD-0103
This is M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01...
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-1892
Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-2001
U Bracket 2mm Hard aluminum Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...
Reference: RBD-2262
Type: Hexagonal coupling. Material: brass. Inner diameter: 8 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-1710
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 12.6gm
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0323
Microcontroller ATmega328 (SMD) – Interface CH340G Operating Voltage: 5V Input Voltage (recommended): 7-12V Digital I / O Pins 14 (of which 6 provide PWM output) RoboticsBD Analog Input Pins: 6 A programming cable is included.
Reference: RBD-0770
Size: 5mm Color: Yellow Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-1393
Double row. 2.54mm pitch. 2 x 20 pins. Through-hole mount. 12mm pin length.