Reference: RBD-1565

Robotic Arm Edge Kit

MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-1659

Double Sided FR-4 PCB Prototype Board 5x7cm

Dimension: 5×7 CM Quantity : 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 10 gm PCB color: Green

Reference: RBD-0034

Servo Motor MG996R 180 Degree Rotation

Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm

Reference: RBD-2151

JoyStick Shield Module Robotics Control

2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V

Reference: RBD-0237

APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW

Description: This Telemetry radio set allows you to link to  a flight controller such as the APM or Multiwii  AIO via a USB equipped device such as a  computer, laptop or tablet supporting a USB  connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)

Reference: RBD-0688

RF Transmitter Receiver Pair 433 MHz

Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.

Reference: RBD-2043

Double Sided FR-4 PCB Prototype Board 9x15cm

Dimension: 9 x 15 cm Type: Double-Sided Quantity: 1 Pcs. Base Material: FR4 Copper Thickness: 1-4 OZ Board Thickness: 1.6

Reference: RBD-1709

6mm Hex coupling for Robot Smart Car Wheel 30mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm

Reference: RBD-0104

6DOF Accelerometer Gyroscope GY-521 MPU-6050

Chip built-in 16bit AD converter, 16-bit data output Driver Chip: MPU6050 Operating Voltage: 3-5V DC Communication: I2C/IIC Protocol Gyro Range: ± 250, 500, 1000, 2000 °/s Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g

Reference: RBD-0549

Breadboard Power Supply Module 3.3V 5V

Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...

Reference: RBD-1398

1 Channel 12V Relay Board Module

Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock

Reference: RBD-0918

Multifunctional Standard Aluminum Servo Bracket

Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. RoboticsBD Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking.

Reference: RBD-1422

Pixy2.1 CMUcam5 Smart Vision Sensor

Processor: NXP LPC4330, 204 MHz, dual core Image sensor: Aptina MT9M114, 1296×976 resolution with integrated image flow processor Lens field-of-view: 80 degrees horizontal, 40 degrees vertical Power consumption: 140 mA typical Power input: USB input (5V) or unregulated input (6V to 10V) RAM: 264K bytes Flash: 2M bytes

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-1560

DC 9V Charging Step Up Booster Module for 18650 Lithium Battery UPS Voltage Converter Protection

Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection

Reference: RBD-0410

X9C103S Digital Potentiometer Module for Arduino

Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)

Reference: RBD-0400

NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs

Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....

Reference: RBD-0442

DC 12V Solenoid Electric Door Lock

Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. RoboticsBD

Reference: RBD-2006

Humanoid Robot Feet Servo Bracket

Feet Bracket 2mm Hard aluminum  Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...

Reference: RBD-0234

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: RBD-1559

DC 12V Charging Step Up Booster Module for 18650 Lithium Battery UPS Voltage Converter Protection

Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection

Reference: RBD-0440

HC-12 433Mhz Wireless Serial Transceiver Module - 1 Kilometer

433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD

Reference: RBD-2004

Oblique U Servo Bracket

Servo U Bracket 2mm Hard aluminum  Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...

Reference: RBD-1880

12V 500RPM 25GA Gear Motor

Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions

Reference: RBD-2058

Brushed DC Motor 12V 250W Gear Reduction Motor for E-bike Wheelchair Robot

Voltage: 12V Rated power: 250W Rated torque: 0.8N.m Rated speed: 2750RPM No loading current: ≤14A Rated current: 20A

Reference: RBD-2163

6V 30:1 500RPM Micro Metal Gearmotor w/ Encoder

Built-in encoder Average output up to 420 pulses per revolution The brass faceplate has two mounting holes threaded Long D profile metal output shaft (0.354"/9.0 mm)

Reference: RBD-0399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.