Reference: RBD-1197

TSOP38236 IR Infrared Receiver

The TSOP38236 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor.

Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-2059

LDR 20 mm Light Depending Resistor

LDR 20 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.

Reference: RBD-2091

MY18E20 DS18B20 Compatible Temperature Sensor Module

Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20

Reference: RBD-2079

38KHz Infrared Transmit Sensor Module

This is 38KHz Infrared IR transmitter sensor module For Arduino Transmit 38KHz modulating signal Suitable for Arduino DIY project Material: PCB

Reference: RBD-2100

Flame Sensor Module Digital & Analog Output

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-0676

MQ-7 Carbon Monoxide Gas Sensor

Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm. RoboticsBD

Reference: RBD-0426

GUVA-S12SD UV Detection Sensor Module

Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity

Reference: RBD-1860

KS-RG22 High Precision Electric Eye Color Sensor

Model KS-RG22 Coaxial reflection type Supply voltage DC10-30V±10%

Reference: RBD-1856

PAM8403 Super Mini Digital Amplifier Board

Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...

Reference: RBD-1512

LDR 10mm Light Depending Resistor

LDR 10 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-1719

Envitec OOM202 Medical Ventilator Oxygen Sensor

Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December

Reference: RBD-0391

AD8232 ECG Measurement Module Kit

Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD

Reference: RBD-0147

HR202 Humidity Detection Sensor Module

Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).

Reference: RBD-2094

DHT11 Digital Relative Humidity and Temperature Sensor Module

The module can detect the surrounding environment of the humidity and temperature High reliability and excellent long-term stability The output from the digital output Humidity measuring range: 20%~90%RH(0~50 degree (temperature compensation). Temperature measuring range: 0~+50degree. Humidity measurement accuracy: ±5.0%RH. Temperature measurement...

Reference: RBD-0677

MQ-8 Hydrogen Gas Sensor

Using high-quality dual-panel design, with power indicator and TTL signal output instructions. The switching signal having a DO (TTL) output and analog output AO. TTL output valid signal is low. The higher the voltage, the concentration of the analog output voltage is higher. A hydrogen gas detection with good sensitivity. Has a long life and reliable...

Reference: RBD-1063

W1209 Digital Temperature Controller

Temperature Control Range(°C): -10 to +50 Resolution @-9.9°C to +99.9°C: 0.1°C Resolution @all temperatures: 1°C Accuracy: 0.1°C Refresh Rate(s): 0.5 Supply Voltage(V): 12 Measuring Inputs: NTC10K Cable Length: 0.5 Meter Output Type: 1 Channel Relay Output Capacity: 10A If you need to measure more than 50c please review this product. XH-W1219 Temperature...

Reference: RBD-0425

GY-9960LLC APDS-9960 RGB and Gesture Sensor Module

Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD

Reference: RBD-0493

RTD PT-100 Temperature Sensor 100mm Probe 0‑400℃

Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;

Reference: RBD-1934

MQ-136 Hydrogen Sulfide Gas Sensor

Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics

Reference: RBD-1946

GY-BME280 3.3V Temperature and Humidity Sensor

Comes with the BME280 sensor. Pressure accuracy of ±1 hPa. Temperature accuracy ±1.0°C. Altimeter accuracy ±1 meter. Humidity: +-3%

Reference: RBD-1858

Photoelectric Sensor CDD-11P Diffuse PNP Infrared Metal Body NO+NC

CDD-11P PNP Output Photoelectric sensor  Epoxy filled housing ensures resistance to vibration Rigid Nickel Plated Brass housing This is PNP Output CDD-11P. For NPN Output CDD-11N please check here.

Reference: RBD-0022

Ultrasonic Sonar Sensor HC-SR04

This is the HC-SR04 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC (Power),...

Reference: RBD-2072

Linear Magnetic Hall sensor

Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light

Reference: RBD-1193

3mm Infrared Emitter and Detector

Infrared Photodiode Transmitter 3mm Infrared Photodiode Receiver 3mm

Reference: RBD-1811

AS5600 Magnetic Induction Encoder Angle Measurement Sensor

AS5600 Magnetic Induction Angle Measurement Sensor

Reference: RBD-0813

Liquid Suspended Particles Turbidity Sensor Detection Module Kit

Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.

Reference: RBD-1111

Geiger Counter Kit Nuclear Radiation Detector Gamma Ray Build Radiation Monitoring Station

This is one open-source Geiger Counter project which could be used to detect nuclear radiation. The schematic and code and other helpful files are listed in this package. All the codes are designed and tested on this kit, these materials are useful for DIY Geiger Counter Kit Nuclear Radiation Detectors or Radiation Monitoring Stations. Note: The kit comes...

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD