How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
If you are wandering to navigate the distance with a drone then this GPS Module is needed for you. GPS drones are equipped with a GPS module that allows them to know their location relative to a network of orbiting satellites. Connecting to signals from these satellites allows the drone to perform functions such as position hold, autonomous flight, return to home, and waypoint navigation.
Neo 7M GPS module that includes an HMC5883L digital compass. The new NEO 7 series is a high sensitivity, low-power GPS module that has 56 channels and outputs precise position updates at 10Hz. This GPS module also comes with a molded plastic case which keeps the module protected against the elements making it ideal for use on your aircraft or quadcopter.
This Neo 7M GPS module uses an active circuitry ceramic patch antenna to provide an excellent GPS signal which outperforms the older Neo 6 series modules. This Neo 7 module also includes a rechargeable backup battery to allow for HOT starts and also includes an I²C EEPROM to store the configuration settings. Out of the box this GPS module is configured to run at 38400 Baud and is configured to run with APM/Pixhawk systems. This GPS module includes two cables, a 6pin connector for the GPS module, and a 4 pin connector for the i2c compass. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Note:
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Model | Ublox NEO 7M |
| UBLOX NEO-7M Receiver Type | 56 Channels Galileo E1B/C1 GPS L1C/A QZSS L1C/A SBAS L1C/A |
| UBLOX NEO-7M Receiver Frequency | L1 [1575.42MHz] |
| UBLOX NEO-7M Input Supply Voltage (VDC) | 3.5 ~ 5.5 |
| UBLOX NEO-7M Main Chip | U-BLOX NEO-7M |
| UBLOX NEO-7MSensitivity (dBm) | -155 -160 Cold Start (without aiding): -147 dBm Tracking & Navigation: -161 dBm |
| UBLOX NEO-7M Position Accuracy (Meter) | 2 2.5 |
| UBLOX NEO-7M Acceleration (g) | <4 |
| UBLOX NEO-7M Navigation Update Rate | 5Hz |
| UBLOX NEO-7M Operating Temperature Range (°C) | -24 to 84 |
| UBLOX NEO-7M Tracking Sensitivity (dBm) | -161 dBm |
| UBLOX NEO-7M Co-Ordinate System | WGS-84 |
| UBLOX NEO-7M Capture Time | 0.1s Average |
| UBLOX NEO-7M Avg Cold Start Time (s) | 38 |
| UBLOX NEO-7M Warm Start Time (s) | 35 |
| UBLOX NEO-7M Boot Time | 1S |
| UBLOX NEO-7M Maximum Altitude (m) | 18000 |
| UBLOX NEO-7M Maximum Speed | 515 m/s |
| UBLOX NEO-7M Dimensions (mm) LxWxH | 60 x 11.5 (DxH) |
| UBLOX NEO-7M Weight (gm) | 26 |
| UBLOX NEO-7M Cable Length (cm) | 20 |
| Compass Stand Holder Material | Aluminium |
| Compass Stand Holder Color | Black |
| Compass Stand Holder GPS Plate Diameter | 40 mm. |
| Compass Stand Holder Base Plate Diameter | 35 mm |
| Compass Stand Holder Weight(gm) | 20 |
| Compass Stand Holder Height | 14 cm. |
| Compass Stand Holder Mounting Hole Spacing: | 16-35mm |
| Compass Stand Holder Mounting Rod Diameter: | Â 4mm |
| Shipment Weight | 0.030 kg |
| Shipment Dimensions | 18 × 18 × 6 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Neo 7M GPS module.
1 x Compass Stand Holder for APM ArduPilot Mega 2.6 Pixhawk Flight Control.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of UBLOX NEO-7M NEO 7M GPS w/ Compass Stand Holder for APM ArduPilot Mega 2.6 Pixhawk Flight Control in Bangladesh is BDT 2,450 You can buy the UBLOX NEO-7M NEO 7M GPS w/ Compass Stand Holder for APM ArduPilot Mega 2.6 Pixhawk Flight Control at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0239
Material: CNC Aluminum alloy, carbon glass fiber rod Mounting rod diameter: 4mm Lead of rod: 14 cm. GPS plate diameter: 40 mm. Base plate diameter: 35 mm Mounting hole spacing: 16-35mm Weight: 20g Colour: Anodised black
Reference: RBD-0300
Model: APM 2.8 Arducopter APM 2.8 Flight Controller Input Voltage (V): 12-16 V. Arducopter APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 Arducopter APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 Ublox NEO 7M GPS Tracking sensitivity: 161 dBm Ublox NEO 7M GPS Capture sensitivity : 148 dBm Ublox NEO 7M GPS cold start time:...
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-1267
Neodymium Magnet Size: Rectangular (BAR) Actual Size - 27.83 x 8.6 x 1.66 mm Note: Magnet size may deviate by up to 5%. If you require precise dimensions, please contact our customer support for exact measurements.
Reference: RBD-1546
Model: APM 2.8 APM 2.8 Flight Controller Input Voltage (V): 12-16 V. APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 NEO-M8N GPS Module Dimensions: Outer diameter 54mm NEO-M8N GPS Module Ready to Connect to All APM FC with 5-pin connector Attached NEO-M8N GPS Module Receiver...
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-3491
The Ardupilot Arduplane Pitot Air Speed Meter Kit is a complete solution for precise airspeed measurement on remote control airplanes and UAVs using the APM 2.5, APM 2.6, or APM 2.6 flight controllers. This kit includes a stand-alone airspeed sensor, pitot tube, silicone tubing, and a 15cm female-to-female servo cable for easy and reliable connection.
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0300
Model: APM 2.8 Arducopter APM 2.8 Flight Controller Input Voltage (V): 12-16 V. Arducopter APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 Arducopter APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 Ublox NEO 7M GPS Tracking sensitivity: 161 dBm Ublox NEO 7M GPS Capture sensitivity : 148 dBm Ublox NEO 7M GPS cold start time:...
Reference: RBD-3490
The APM Airspeed Pitot Tube is a precision airspeed measurement accessory designed for use with Ardupilot and Arduplane flight control systems. Operating based on differential air pressure detection, this pitot tube measures the dynamic pressure difference between the direct airflow and the static ambient pressure, providing essential data for accurate...
Reference: RBD-0959
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Reference: RBD-0938
ATmega328P with Arduino bootloader MAX7456 monochrome on-screen display FTDI cable compatible pinout Standard 6 pin ISP header 2 independent power sections with an LED indicator on each Solder jumpers for combining the power sections
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-0237
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: RBD-3412
The High Precision GPS M8N 8M is a next-generation GNSS module designed for high-accuracy navigation and flight control systems. With its built-in compass and versatile stand holder, this GPS module ensures stable positioning, reduced signal interference, and seamless integration with flight controllers like APM 2.6, 2.8, and Pixhawk 2.4.6, 2.4.8.
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-0288
Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v
Reference: RBD-1546
Model: APM 2.8 APM 2.8 Flight Controller Input Voltage (V): 12-16 V. APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 NEO-M8N GPS Module Dimensions: Outer diameter 54mm NEO-M8N GPS Module Ready to Connect to All APM FC with 5-pin connector Attached NEO-M8N GPS Module Receiver...
Reference: RBD-2620
Compact and lightweight F3 flight controller for brushed drones. Built-in receiver options for various brands (FlySky, Frsky, etc.). Integrated 4-in-1 brushed ESCs for simplified wiring. Supports CleanFlight and BetaFlight firmware for customization. Plug-and-play compatible with MX VTX 25MW module and camera.
Reference: RBD-2506
The SF Racing F3 flight controller is designed to provide high performance flight experience for the hobbyists. With verified sensor algorithm, it provides incomparable I/O capabilities. The SF Racing F3 runs a next-generation 32-bit STM32F303CCT6 processor, an MPU6500 accelerometer and a gyroscope sensor, all high integrated on a lightweight PCB to...
Reference: RBD-2507
Operating voltage: 3~5 V Resolution: 1cm Response frequency: 15 HZ (full range) Operating current: 9mA (vcc = 5v) Operating temperature: -20℃ -65℃ Storage temperature: -40℃ -85℃ Measurement range: 20cm ~ 720cm (vcc = 5v) Package Included: 1Pc GY-US42 Ultrasonic Distance Measuring Module
Reference: RBD-0228
Color: Black Material: Glass-fiber Suit for different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4 Package Weight: 24 gm.
Reference: RBD-0216
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-0942
Manufacturer: AMASS Type of connector: DC supply Connector series: XT60H Kind of connector: Female Number of pins: 2
Reference: RBD-0953
High-Quality Carbon fiber Material Frame Comes With Landing Gear Power Distribution Board Pre Installed Easy to Assemble kit
Reference: RBD-0931
Weight : 190 gm Voltage: 11.1V Capacity: 3300mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-0228
Color: Black Material: Glass-fiber Suit for different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4 Package Weight: 24 gm.
Reference: RBD-2010
Capacity (mAh): 960-1500 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-0719
Bandwidth (KHz): 500. RF Range (GHz): 2.40 ~ 2.48. No. of channels: 6. Remote controller weight (gm): 400. Power: 6V (1.5V AA*4). Antenna Length: 26mm * 2 (dual antenna). Transmitting Power: ≤ 20dBm. RF Receiver Sensitivity: -105dbm. RoboticsBD
Reference: RBD-0931
Weight : 190 gm Voltage: 11.1V Capacity: 3300mAh Cell Type: Li-polymer Configurations: 3S Continuous Discharge Rate: 25C Max Burst Rate: 90C Discharge(Output) Lead: T Plug Connector Charging(Balancing) Lead: JST-XHR Wire Length: 100mm Operating Temperature Range: -20℃to 60℃ PVC color: Silver and Black
Reference: RBD-0556
Framework: 12N14P KV: 1400KV LiPO Batteries: 2-3S Max. thrust: 930-940gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-0953
High-Quality Carbon fiber Material Frame Comes With Landing Gear Power Distribution Board Pre Installed Easy to Assemble kit
Reference: RBD-0216
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-0228
Color: Black Material: Glass-fiber Suit for different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4 Package Weight: 24 gm.
