Reference: RBD-1219

3.5inch Touch LCD Shield for Arduino

Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display, support for touch function Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage Easy to expand...

Reference: RBD-2207

AD9850 DDS Signal Generator Module

2 sine wave and 2 square wave output. AD9850: 0-40MHz. After the 20-30MHz frequency harmonics increases, the waveform will be less and less clean. Low-pass filter with 70MHz, so the waveform better than SN. Parallel and serial data input can be selected via a jumper.

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-2213

TPA3118 PBTL Mono Digital Amplifier Board 1X60W 12V 24V Power Amplifier Module

Operating voltage (v):DC 8 – 24V Chipset:TPA3118 Power output:60W Material:FR4

Reference: RBD-2100

Flame Sensor Module

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-0742

Motor Driver 43A BTS7960

Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.

Reference: RBD-1541

37 In 1 Sensor Module Board Set Kit For Arduino with Box

For beginners who are interested in Arduino A complete set of Arduino’s most common and useful electronic components Infrared sensor receiving module Laser sensor module Temperature and humidity sensor module Infrared sensor module 5v relay module Obstacle avoidance sensor module.

Reference: RBD-1021

PAM8406 5Wx2 Class D Digital Stereo Audio Power Amplifier Module Board

Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g

Reference: RBD-1750

Instrumentation Voltage Amplifier Module AD620

Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV

Reference: RBD-1368

8 Channel Logic Level Converter

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0028

Arduino Ethernet Shield W5100

Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...

Reference: RBD-1332

I2C Graphic 128x64 LCD Adapter

Adapter: Graphic 128x64 Communication: i2c 

Reference: RBD-2134

433Mhz Wireless Receiver Learning Code EV1527 Decoding Module 4Ch output With Learning Button

433 Mhz Wireless Receiver Learning Code 1527 Decoding Module 4 Ch output With Learning Button diy kit For Arduino/ARM/MCU For Wireless Power switch socket remote control LED electric doors Etc.

Reference: RBD-2075

MQ-2 Gas sensor Module

MQ-2 Smoke Gas Detector Sensor  ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s

Reference: RBD-1928

HC-08 Bluetooth 4.0BLE Serial Port Module

Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.

Reference: RBD-2082

Infrared IR Sensor Receiver Module for Arduino

Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.

Reference: RBD-0348

Heart Rate Pulse Sensor Module For Arduino

A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1911

XD-21 LM358 Gain Amplification Module Operational Amplifier Module

LM358 chip onboard. 100 gain of the circuit design. 10K onboard adjustable resistance, you can adjust the magnification. Onboard power indicator. The chip has led major pin can be directly input and output signals.

Reference: RBD-0400

NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs

Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....

Reference: RBD-2230

NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator

Main chip: NE555 Input Voltage: 5V-15V DC. Generate an adjustable pulse for MCU. Generate an adjustable pulse, to control circuitry associated.

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-2216

PCF8591 Module Analog to Digital / Digital-Analog Converter Module

Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...

Reference: RBD-1409

Arduino Compatible Red Laser Diode Module

Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C.

Reference: RBD-0108

USB Host Shield For Arduino UNO, MEGA, Compatible with Google Android ADK

Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...

Reference: RBD-1137

Mini ENC28J60 Ethernet LAN Network Module For Arduino

Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...

Reference: RBD-1773

VHM-314 V3.0 Bluetooth Audio Receiver Board

Supply Voltage: 5V USB / 3.7V lithium battery Output Port: 3-wire audio interface/DIY pad Output Type: Analog signal Bluetooth name: VHM-314-V3.0 Bluetooth version: 5.0 Bluetooth passcode: no password Sound source: Bluetooth. USB-PC input(after the back pad is connected, the computer can be connected as a sound card though Micro) Operation method:...

Reference: RBD-1328

0.96" Inch I2C OLED Display White

Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A