Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-1333

Button Keypad 3x4 module (Assembled)

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)

Reference: RBD-2213

TPA3118 - 28p PBTL Mono Digital Amplifier Board 1X30W 12V Power Amplifier Module

Operating voltage (v):DC 8 – 12V Chipset:TPA3118 - 28 pin Chinese Variant Power output:30W Material:FR4 This is a Chinese variant of the TPA3118 in a 28-pin package.

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-2090

Magic Cup Tilt Switch Module

Operates on 5V DC supply. Mercury switch

Reference: RBD-0980

NeoPixel NeoMatrix 8x8 - 64 RGB LED Pixel Matrix WS2812 5050 RGB LED

Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.

Reference: RBD-2120

HW670 5A Current Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.

Reference: RBD-2243

LilyPad Button Board

Wearable e-textile technology.  Designed with large sew tabs Button Board

Reference: RBD-2100

Flame Sensor Module Digital & Analog Output

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-2083

Analog Temperature Sensor Module

Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.

Reference: RBD-2078

Vibration Switch Module

No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA

Reference: RBD-0990

XFS5152CE Speech Synthesis Module TTS Voice Module

Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.

Reference: RBD-2156

4×4 Matrix 16 Keyboard Keypad

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-0915

UART EM4100 RFID Card Reader RDM6300

Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-1738

Active Speaker Buzzer Module for Arduino 5V

Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH):  26 x 15 x 11 mm

Reference: RBD-2216

PCF8591 Module Analog to Digital / Digital-Analog Converter Module

Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...

Reference: RBD-1815

PC817 4 Channel Optocoupler Isolation Board

I/O Isolation for MCUs (Micro Controller Units) Noise Suppression in Switching Circuits Driving Port Signal Voltage: 3.6-24V Output Port Voltage Port: 3.6-30V Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.

Reference: RBD-2209

Servo Motor Controller Driver Board 16 Channels High Accuracy MCU Software

16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms

Reference: RBD-2223

MOSFET Electronic Switch DC Controlling Board

Input Voltage: 3 V ~ 20 V Input Current: 5mA Output Voltage: 5 V ~ 35 V Output Current: 5A Item Dimensions: 46 * 25 * 18mm

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-2041

360 Degree Rotary Encoder Brick Sensor Module

Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.

Reference: RBD-1541

37 In 1 Sensor Module Board Set Kit For Arduino with Box

For beginners who are interested in Arduino A complete set of Arduino’s most common and useful electronic components Infrared sensor receiving module Laser sensor module Temperature and humidity sensor module Infrared sensor module 5v relay module Obstacle avoidance sensor module.

Reference: RBD-2226

2 Channel 24V Relay Board Module with OPTO Isolation Support High or Low Level Trigger

Operating Voltage: 24V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...

Reference: RBD-2094

DHT11 Digital Relative Humidity and Temperature Sensor Module

The module can detect the surrounding environment of the humidity and temperature High reliability and excellent long-term stability The output from the digital output Humidity measuring range: 20%~90%RH(0~50 degree (temperature compensation). Temperature measuring range: 0~+50degree. Humidity measurement accuracy: ±5.0%RH. Temperature measurement...

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-0400

NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs

Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....

Reference: RBD-1266

Prototype Shield With Breadboard for Arduino

It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...