

This straight bar load cell (sometimes called a strain gauge) can translate up to 5 kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the bar.
With this gauge, you will be able to tell just how heavy an object is, if an object’s weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load applied to a surface. This straight bar load cell is made from an aluminum alloy and is capable of reading a capacity of 1KG of weight RoboticsBD
It has Four lead wires which can be connected to HX711 A/D PRESSURE SENSOR It is easy to use with driving voltage 5-10V and produce the output voltage as per the force changes over it. RoboticsBD
Installation of the Sensor is also the simple task, it needs to fix one end through the screw hole and the other end left floating state, according to the label indicates the direction of the gravitational force exerted particular attention must not directly push the white plastic cover part of the sensor in order to avoid damage. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Model | YZC-131A |
Material | Aluminum |
Dimensions in mm (LxWxH) | 75x13x13 |
Weighing Range (Kg) | 0 ~ 5 |
Rated Output | 1.0 ± 0.1mV / V |
Non Linear Output | ± 0.03% F.S |
Hysteresis | 0.0% F.S |
Repeatability | 0.05% F.S |
Creep | (5 minutes) 0.05% F.S |
Cable Length (cm) | 18 |
Zero Balance | ± 0.1 mV / V |
Impedance (Ω) | 1066 ± 10% Ω |
Output Impedance | 1000 ± 10% Ω |
Temperature Effect on Output | 0.003% F.S / C |
Operating Temperature Range (°C) | -21 to 40 |
Weight (gm) | 29 |
Insulation Resistance (MΩ) | 2000 |
Shipment Weight | 0.08 kg |
Shipment Dimensions | 8 × 3 × 1 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Weighing Load Cell Sensor 5kg YZC-131 With Wires.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Weighing Load Cell Sensor 5kg in Bangladesh is BDT 380 You can buy the Weighing Load Cell Sensor 5kg at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0661
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-1172
Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy to install. Strong anti-interference ability Suitable for corridor, toilet,...
Reference: RBD-1380
Sharp GP2Y0A02YK0F IR Range Sensor - 20 cm to 150 cm Infrared range finder 20cm (~8") to 150cm (~60") Distance measuring range: 20 cm to 150 cm (8″ to 60″) Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-0419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: RBD-1178
Size: 5mm Emitted Color : UV View Angle: About 20 - 25 degree. Luminous Intensity: 800mcd-2500mcd
Reference: RBD-0315
Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD
Reference: RBD-0664
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD
Reference: RBD-0671
Operating Voltage:+5V Preheat Duration:20 s Analog Output Voltage:0 to 5 V Dimension:36x20x21 mm. RoboticsBD
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-2082
Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.
Reference: RBD-0491
Sensor Type: Inductive Sensing Distance: 0.197" (5mm) Output Type: NPN-NO, 3-Wire Response Frequency: 400Hz
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-1654
5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector Color Black
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-2092
Product Type: LED Shape: Round LED 5mm DIP type Color: pink yellow-green (high brightness) Lens type: white mist Standard Forward Voltage:3.0-4 .5 V
Reference: RBD-1423
Sony IMX477R stacked, back-illuminated sensor. Resolution: 12.3 megapixels. Compatible with Raspberry Pi 1/2/3/4 boards Output: RAW12/10/8, COMP8 Back focus: Adjustable (12.5 mm–22.4 mm) Lens standards: C-mount, CS-mount (C-CS adapter included) IR cut filter: Integrated Wide Field of View suitable for CCTV applications Suitable for macro photography...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-2211
Soil moisture sensor module Digital and analog output Adjustable threshold Waterproof and corrosion-resistant probe
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-1833
NEW TYPE AVAILABLE CLICK HERE Measurement range: 0-199 mg/KG Measurement accuracy: +-2%F.s Resolution: 1mg/KG (mg/L) Response time (T90, s): less than 10 Communication port: RS485 Power supply: 5V-24v DC
Reference: RBD-1199
Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance
Reference: RBD-2089
Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected.
Reference: RBD-1934
Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics
Reference: RBD-0665
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-2125
Phototransistor output No contact surface sensing Miniature package
Reference: RBD-1190
Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance 10kΩ Tolerance: ±1% Maximum Power Rating: 75mW Maximum Operating Temperature: +150°C Minimum Operating Temperature: -80°C Dimensions(dia.): 2 mm Length: 30mm Application: Compensation, Control, Measurement, etc.
Reference: RBD-1162
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc
Reference: RBD-1687
Model No.: ISR18650-1300 Capacity (mAh): 750-1300 (Copy) Output Voltage: 3.7V High energy density High working voltage for single battery cells. It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-2194
This 60/40 Tin-Lead solder contains 60% Sn (Tin) / 40% Pb (Lead) 170° - 185°C melting range Premium Quality Soldering Wire/Lead Low Melting Point Weight: 20-22 Gram 0.8mm Mix: 60% Sn / 40% Pb Known as Lead or Solder Wire Melting Temperature 170°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your...
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD