

This weighing Load Cell Sensor (sometimes called a strain gauge) can translate up to 1 kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the bar. RoboticsBD
With this gauge, you will be able to tell just how heavy an object is, if an object’s weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load applied to a surface. This straight bar load cell is made from an aluminum alloy and is capable of reading a capacity of 1KG of weight
It has Four lead wires which can be connected to HX711 A/D Pressure Sensor. It is easy to use with driving voltage 5-10V and produce the output voltage as per the force changes over it.
Installation of the Sensor is also the simple task, it needs to fix one end through the screw hole and the other end left floating state, according to the label indicates the direction of the gravitational force exerted particular attention must not directly push the white plastic cover part of the sensor in order to avoid damage. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Model | YZC-131 |
Material | Aluminium |
Dimensions in mm (LxWxH) | 75 x 12.6 x 12.6 |
Weighing Range (Kg) | 0 ~ 1 |
Rated Output | 1.0 ± 0.1mV / V |
Non Linear Output | ± 0.03% F.S |
Impedance (Ω) | 1066 ± 10% Ω |
Output Impedance | 1000 ± 10% Ω |
Insulation Resistance (MΩ) | 2000 |
Hysteresis | 0.03% F.S |
Repeatability | 0.03% F.S |
Creep | (5 minutes) 0.05% F.S |
Zero Balance | ± 0.1 mV / V |
Cable Length (cm) | 18 |
Operating Temperature Range (°C) | -20 to 65 |
Weight (gm) | 26 |
Shipment Weight | 0.08 kg |
Shipment Dimensions | 12 × 5 × 4 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Weighing Load Cell Sensor 1Kg for Electronic Scale.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Digital Electronic Weighing Sensor (Scale 1 Kg) Loadcell in Bangladesh is BDT 300 You can buy the Digital Electronic Weighing Sensor (Scale 1 Kg) Loadcell at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0133
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-1018
Dimensions: 75 x 13 x 13 mm (L x W x H) Range: 5 kg Cable Length: 18 cm Fitting ScrewHole Size: M3 Rated output: 1.0 0.1mV / V Nonlinear: 0.05% F.S Hysteresis: 0.0% F.S Repeatability: 0.05% F.S
Reference: RBD-2221
Microwave sensor module Uses 10.525 GHz band to detect movement Easy to use, can be connected directly to a microcontroller Built-in amplifier Ideal for use with a microcontroller Widely used in industrial, transportation, and civil devices
Reference: RBD-1203
Distance measuring range: 10 cm to 80 cm Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-1644
940nm laser classified as class 1 under operation condition by IEC 60825-1:2014-3rd edition Small ceramic package(20×13.2×2.0mm) Long range absolute range measurement up to 1.8m within 5% accuracy at indoor
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-1424
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-2080
Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A fixed bolt holes for easy installation
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modulesChinese Variant MP92 QFN24 Package
Reference: RBD-0683
Operating voltage: DC3-5V Operating current: less than 20mA Sensor Type: Analog Detection Area: 40mmx16mm Operating temperature: 10℃-30℃ Humidity: 10% -90% non-condensing
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-0555
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Reference: RBD-1063
Temperature Control Range(°C): -10 to +50 Resolution @-9.9°C to +99.9°C: 0.1°C Resolution @all temperatures: 1°C Accuracy: 0.1°C Refresh Rate(s): 0.5 Supply Voltage(V): 12 Measuring Inputs: NTC10K Cable Length: 0.5 Meter Output Type: 1 Channel Relay Output Capacity: 10A If you need to measure more than 50c please review this product. XH-W1219 Temperature...
Reference: RBD-2059
LDR 20 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.
Reference: RBD-2206
Analog piezoelectric ceramic vibration module Measures the extent of vibration Proportional to the strength of shock or vibration Interface type: Analog Output Dimensions: 30 (L) x 23 (W) x 17 (H) Weight: 5g
Reference: RBD-0689
Operating Voltage: 2.8 V to 5.5 V Accuracy: ± 1.5°C Zero power resistance: 100 KΩ Operating temperature range: -55 ~ +125 ℃
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-2237
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Clear sound Ultra-thin and lightweight No contacts: therefore, no noise and highly reliable Operating Temperature: -20~70 Storage Temperature: -30-80
Reference: RBD-1717
Wide voltage operation: 3.3~5.5V 0~2.3V analog signal output, compatible with 5V, 3.3V two control systems The excitation source is an AC signal, effectively preventing probe polarization Waterproof probe for long-term immersion in water
Reference: RBD-2083
Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-1423
Sony IMX477R stacked, back-illuminated sensor. Resolution: 12.3 megapixels. Compatible with Raspberry Pi 1/2/3/4 boards Output: RAW12/10/8, COMP8 Back focus: Adjustable (12.5 mm–22.4 mm) Lens standards: C-mount, CS-mount (C-CS adapter included) IR cut filter: Integrated Wide Field of View suitable for CCTV applications Suitable for macro photography...
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0722
8-Megapixel native resolution high-quality Sony IMX219 image sensor Cameras are capable of 3280 x 2464 pixel static images Capture video at 1080p30, 720p60 and 640x480p90 resolutions All software is supported within the latest version of Raspbian Operating System No Infrared filter making it perfect for taking Infrared photographs or photographing objects...
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-0675
Model: MQ-6 Operating Voltage: 5V DC Detecting Range:200-10000 ppm Relative Humidity:<95% RH
Reference: RBD-1066
Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...
Reference: RBD-2130
9DOF IMU module with compass, acceleration, and gyroscope sensors Captures nine different types of motion or orientation Measures 3-axis gyroscope, triaxial accelerometer, and triaxial magnetic field Power supply: 3-5V (internal low dropout regulator)
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-1875
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-1349
For Standard LCD 16x2. Press here.For Standard LCD 16x2 with Male Header. Press hereFor Standard LCD 16x2 with Female Header. Press hereFor Standard LCD 16x2 with I2C adapter board soldered. Press here.For Standard LCD 16x2 with White Background. Press here.For Standard LCD 16x2 with Blue Background. Press here. Model: LCD1602 Interface: I2C Interface...
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C