Reference: RBD-0382

GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module

3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD

Reference: RBD-2085

PCB Mounted Passive Buzzer Module

Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH):  26 x 15 x 11 mm

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1347

TTP223 Capacitive Touch switch Digital Touch Sensor Module For Arduino

TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.

Reference: RBD-1914

Reed Switch Module

Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation

Reference: RBD-2100

Flame Sensor Module Digital & Analog Output

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-0830

Thermocouples - K Type 800C WRN-291 200mm Rod

Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree.  Screw Type

Reference: RBD-1856

PAM8403 Super Mini Digital Amplifier Board

Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...

Reference: RBD-0426

GUVA-S12SD UV Detection Sensor Module

Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity

Reference: RBD-1422

Pixy2.1 CMUcam5 Smart Vision Sensor

Processor: NXP LPC4330, 204 MHz, dual core Image sensor: Aptina MT9M114, 1296×976 resolution with integrated image flow processor Lens field-of-view: 80 degrees horizontal, 40 degrees vertical Power consumption: 140 mA typical Power input: USB input (5V) or unregulated input (6V to 10V) RAM: 264K bytes Flash: 2M bytes

Reference: RBD-1173

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 100A

Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties

Reference: RBD-1640

12V Gas Detector Sensor Alarm Propane Butane LPG Natural

Color: White Material: Metal + Plastic Operating Voltage : 12V DC Standby Current : ≤90mA Alarm Current : ≤100mA

Reference: RBD-0312

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Reference: RBD-1179

LM35 Temperature Sensor Waterproof

Temperature measuring range: 0...100°C Typical Input Voltage:3.3VDC,5VDC Operating Current:60uA Interface: Analog ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase unless you're confident that you can use it successfully.

Reference: RBD-2091

MY18E20 DS18B20 Compatible Temperature Sensor Module

Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20

Reference: RBD-0673

MQ-4 Methane Natural Gas Sensor

Detecting range: 300~10000ppm Signal output indicator. Dual Signal output (analog output and TTL output). The TTL output signal is low level, allows us to connect with SCM directly. Analog output 0~5V voltage. Quick response and recovery. RoboticsBD

Reference: RBD-1860

KS-RG22 High Precision Electric Eye Color Sensor

Model KS-RG22 Coaxial reflection type Supply voltage DC10-30V±10%

Reference: RBD-0664

ADXL345 Triple Axis Accelerometer Breakout

Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD

Reference: RBD-0676

MQ-7 Carbon Monoxide Gas Sensor

Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm. RoboticsBD

Reference: RBD-1193

3mm Infrared Emitter and Detector

Infrared Photodiode Transmitter 3mm Infrared Photodiode Receiver 3mm

Reference: RBD-1854

Resistive Film Pressure Sensor Module Pin Header Analog Signal 200mm

This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.

Reference: RBD-1699

Brand: SparkFun Electronics

REDBOT SENSOR - MECHANICAL BUMPER

Simple switches Detect a collision SPST switch

Reference: RBD-0391

AD8232 ECG Measurement Module Kit

Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD

Reference: RBD-1931

Soil NPK Sensor Agricultural RS485/Modbus

Easy to Measure High Precision Low measurement cost Resolution up to 1mg/kg (mg/l)

Reference: RBD-2082

Infrared IR Sensor Receiver Module for Arduino

Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.

Reference: RBD-0672

MQ-3 Alcohol Gas Sensor

Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output:  0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.

Reference: RBD-1424

ZMCT103C 5A Range Single Phase AC Micro Current Transformer Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-1049

Snow Rain Drops Steam Detection Sensor Module

Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation

Reference: RBD-2073

A3144 Hall Effect Sensor Module

Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.

Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F