Reference: RBD-2243

LilyPad Button Board

Wearable e-textile technology.  Designed with large sew tabs Button Board

Reference: RBD-1923

PWM to Voltage Converter Module 0-100% to-10V

Conversion range: 0% -100% PWM to 0-10v voltage PWM signal reception frequency range: 1KHz – 3KHz Operating voltage: 12V – 30V DC Allowable error: 5%

Reference: RBD-2057

CH9350 USB Serial Module HID Keyboard Mouse Barcode Reader For Arduino

Access multiple interfaces simultaneously  Serial Communication Smaller Volume Wide Range of applications You can access the sample code and documents for this product by visiting your order history page.

Reference: RBD-0028

Arduino Ethernet Shield W5100

Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-1738

Active Speaker Buzzer Module for Arduino 5V

Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH):  26 x 15 x 11 mm

Reference: RBD-1759

Brand: Waveshare

E-Ink Electronic E-paper Display Screen Module 200x200, 1.54inch

Display Resolution: 200 x 200 Display Screen Color: Black and White No backlight so keeps displaying last content for a long time even when the power is down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.

Reference: RBD-2084

Digital Temperature Module

Power supply: 3 – 5V Good sensitivity The output format: Digital switching output (0 and 1) The comparator output signal is clean, good waveform, driving ability, more than 15mA. A fixed bolt holes for easy installation. Using a wide voltage LM393 comparator.

Reference: RBD-1928

HC-08 Bluetooth 4.0BLE Serial Port Module

Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.

Reference: RBD-2145

L298P Motor Driver Shield for Arduino

L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-2157

4×3 Matrix 12 Keyboard Keypad

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.

Reference: RBD-1684

Arduino Pro Mini PLC Relay Board

8 Channel DC 12V Pro mini Relay Shield Module PLC Timer Board for Arduino 

Reference: RBD-1137

Mini ENC28J60 Ethernet LAN Network Module For Arduino

Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...

Reference: RBD-2088

Tilt Switch Sensor Module For Arduino

Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-0702

1 Channel 5V Relay Board Module

It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock

Reference: RBD-1815

PC817 4 Channel Optocoupler Isolation Board

I/O Isolation for MCUs (Micro Controller Units) Noise Suppression in Switching Circuits Driving Port Signal Voltage: 3.6-24V Output Port Voltage Port: 3.6-30V Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.

Reference: RBD-2216

PCF8591 Module Analog to Digital / Digital-Analog Converter Module

Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...

Reference: RBD-1762

Mini BD243 Bubble 9-12V Tesla Coil Electronics Wireless PCB Module

Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm):  3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.

Reference: RBD-2219

ESP32-IO Shield Expansion Board for Arduino WIFI ESP32

ESP32-IO shield Compatible with RoboticsBD ESP32 Core board Brings out all the pins of RoboticsBD ESP32 Core board 2 rows of 2.54mm pin headers for connecting other sensors Power supply circuit for RoboticsBD ESP32 Core board DC 7-12V voltage input DIP switch for controlling the power

Reference: RBD-2220

Full Color LED Module SCM Light Water 5050 LED Module For Arduino

Good PRINT PACK design, very beautiful. 8 world of the three primary colors (red-green-blue) LED color, scanning control mode. Applicable for various platforms, such as 51 / AVR / AVR / ARM / for Arduino All kinds of platforms.

Reference: RBD-2142

CH340C WIFI Module Adapter Download Debug for ESP8266 ESP-01/01S

Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.

Reference: RBD-0937

Mini Data Logger Module

SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...

Reference: RBD-2065

JQ6500 HW-896 V1.2 Voice Sound MP3 Player Module

Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts

Reference: RBD-550

Voice Recognition Module Kit V3.1 Elechouse

Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD

Reference: RBD-2232

TPA3116 2.1 50Wx2+100W Bluetooth CSR4.0 Class D Power Amplifier

Working mode: Class D Operating voltage: DC18V to DC24V Rated output power: 100W + 2 x 50W Quiescent current: 60mA Work efficiency: 90%

Reference: RBD-1911

XD-21 LM358 Gain Amplification Module Operational Amplifier Module

LM358 chip onboard. 100 gain of the circuit design. 10K onboard adjustable resistance, you can adjust the magnification. Onboard power indicator. The chip has led major pin can be directly input and output signals.

Reference: RBD-2238

LilyPad SMD LED Blue Color

Wearable e-textile technology.  Designed with large sew tabs LED Blue Color

Reference: RBD-2041

360 Degree Rotary Encoder Brick Sensor Module

Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.