Reference: RBD-1880

12V 500RPM 25GA Gear Motor

Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions

Reference: RBD-0208

Off-Road Wheels - 130x60mm (Pair)

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-0651

9V Battery Connector

Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black. Battery not included. The device contains a battery that you may need to replace.

Reference: RBD-0360

Polulu RP5 Tracked Chassis Gray

Durable plastic body 6-AA battery holder included two brushed DC motors with 210 mA free run and 2.4 A stall current at 7.2 V maximum speed of 6 in/s (15 cm/s) at 7.2 V

Reference: RBD-0227

JF-0530B Pull Push Type Electric Solenoid Electromagnet 10mm 5N DC6V

Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0741

433MHz 100 Meters ASK Wireless Module Kit RF

Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards

Reference: RBD-1252

Makeblock mBot Ranger 3-in-1 educational robot kit

Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes

Reference: RBD-1539

EL Wire-Red 3m With Pocket Inverter

Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: RED

Reference: 0828

Single Axis Servo Bracket

Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...

Reference: RBD-1400

4 Channel 12V Relay Board Module

4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...

Reference: RBD-0375

Lynxmotion AL5D 4DOF Robotic Arm SSC-32U Combo Kit (FlowBotics Studio)

AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)  

Reference: RBD-0948

ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi

Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...

Reference: RBD-0120

Breadboard Half Size Bare 400 Tie Points

400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips

Reference: RBD-1901

XH-M604 Battery Charger Control Module

 Input Voltage: DC 6-60V Display Accuracy: 0.1V Control Accuracy: 0.1V Output Type: direct output Voltage Tolerance: ±0.1V Apply For:6-60V Lithium Lead-acid battery

Reference: RBD-2258

85mm Antiskid Wheel (Pack of 4)

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Black Tire + Blue Rim If you need to purchase single 85mm Wheel. Vist here. Note: Hex coupling not...

Reference: RBD-0716

65mm Rubber Wheel with 25GA Motor Mounting Bracket

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.

Reference: RBD-0108

USB Host Shield For Arduino UNO, MEGA, Compatible with Google Android ADK

Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...

Reference: RBD-1311

mDrawbot kit

mDrawBot is a 4-in-1 drawing robot kit  it can be assembled into 4 different drawing robots:  mScara. mCar.  mSpider.  mEggBot.

Reference: RBD-2151

JoyStick Shield Module Robotics Control

2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-0575

PH Meter Digital Tester Aquarium Pool Water Urine Wine LCD Pen Monitor Protable

Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration

Reference: RBD-0326

4WD Smart Robot Chassis Kit

Very handy and simple in assembling/disassembling. RoboticsBD Strong components so as to withstand extreme terrain conditions. Transparent Car Chassis. Attractive design. RoboticsBD

Reference: RBD-0442

DC 12V Solenoid Electric Door Lock

Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. RoboticsBD

Reference: RBD-0041

Smart Speed Detecting Sensor for Arduino

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-0233

Brand: SparkFun Electronics

SparkFun 9 Degrees of Freedom IMU Breakout - LSM9DS0

Description: This is the LSM9DS0, a versatile motion-sensing  system-in-a-chip that houses a 3-axis accelerometer, 3-axis  gyroscope, and 3-axis magnetometer. That’s right, 9 degrees  of freedom (9dof) from a single IC!

Reference: RBD-1658

Double Sided FR-4 PCB Prototype Board 4x6cm

Dimension: 4×6 CM Quantity: 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 6 gm PCB color: Green

Reference: RBD-0032

Arduino Nano

USB Driver: CH340 Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please select...

Reference: RBD-0040

Arduino Bluetooth Module HC-06

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-0658

FTDI USB to TTL Serial Converter Adapter FT232RL

Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...