Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1199

Hall Effect Sensor A1302 49E

Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance 

Reference: RBD-0830

Thermocouples - K Type 800C WRN-291 200mm Rod

Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree.  Screw Type

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-0923

DHT22 Original AM2302 Digital Temperature Humidity Sensor Module

Measuring range: temperature -40-80 ℃; humidity 0; 99.9%RH Measurement accuracy (25℃): temperature: + 0.5; humidity: + 2%RH (10; 90%RH) Resolution: temperature: 0.1 ℃, humidity: 0.1%RH Attenuation value: temperature: <1℃ / year; humidity: < 1%RH/ years High precision Capacitive type Full range temperature compensated Relative humidity and...

Reference: RBD-1717

TDS Meter V1.0 Module Water Quality Sensor for Arduino

Wide voltage operation: 3.3~5.5V 0~2.3V analog signal output, compatible with 5V, 3.3V two control systems The excitation source is an AC signal, effectively preventing probe polarization Waterproof probe for long-term immersion in water

Reference: RBD-0678

MQ-9 Gas Leakage Detection Sensor

Good sensitivity to CO/Combustible Gas High sensitivity to Methane, Propane, and CO Long life and low cost Simple drive circuit Input voltage: DC 5±0.2V Current Consumption: 150mA

Reference: RBD-0572

VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB W/ I2C Interface Arduino

Operating Power: 60mW/15fpsVGAYUV. Sleeping Mode: <20 uA. Lens Size: 1/6″. Max. Frame Rate: 30fps VGA. Sensitivity: 1.3V / (Lux-sec). dynamic range: 52 dB. Electronic Exposure: 1 to 510 row.

Reference: RBD-0368

Force Sensitive Resistor 0.5"

Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ)  Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C  Lifespan: >1million times Hysteresis: +10%，(RF+ -RF-)/FR+，1000g...

Reference: RBD-1177

4-20mA Signal Generator Current Loop Simulator Tester

This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...

Reference: RBD-0689

LM75A IIC I2C High Accuracy Digital Temperature Sensor

Operating Voltage: 2.8 V to 5.5 V Accuracy: ± 1.5°C Zero power resistance: 100 KΩ Operating temperature range: -55 ~ +125 ℃

Reference: RBD-0429

BH1750FVI Digital Light intensity Sensor

High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface

Reference: RBD-1347

TTP223 Capacitive Touch switch Digital Touch Sensor Module For Arduino

TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.

Reference: RBD-1716

PM2.5 Air Quality Sensor PMS5003 High Precision Digital Output Module

Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L＜0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi. 

Reference: RBD-2056

PT-100 RTD Temperature Sensor 3 Wire 50cm

Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5sSize: 4*30*500mmRange: -50C ~ 200C

Reference: RBD-1914

Reed Switch Module

Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation

Reference: RBD-1200

IR Infrared Receiver Diode - TSOP38238

Very low supply current Photo-detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light

Reference: RBD-0415

801S Vibration Sensor Module

Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD

Reference: RBD-0023

HC-SR501 PIR Motion Sensor

Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default)  Work temperature: -20-+80°C

Reference: RBD-0222

35mm Piezo Ceramic Elements Sound Sensor

Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound

Reference: RBD-0493

RTD PT-100 Temperature Sensor 100mm Probe 0‑400℃

Temperature Range : 0C-400C Shield Material : Metal Total Length(Approx.) : 2M / 6.6 Ft; Weight : 46g;

Reference: RBD-1847

Pressure Sensors with Display SPABT-P10-R18-2N-K1-SA

Compact Design Country Specific pressure Multiple Displayable Unit Multi-colored, two-part display Alphanumeric display Discontinued by Manufactured 2017

Reference: RBD-1174

Current Sensor ACS712-5A

Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.

Reference: RBD-0417

Force Sensor Resistor Square 38.1mm

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-0149

Flame Sensor Fire Detection Module

Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...

Reference: RBD-0163

HSM-20G Analog Temperature & Humidity Sensor

Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V    Output voltage range (corresponding to 0-100%RH) DC 1-3.19V    Test accuracy 5% RH

Reference: RBD-1207

Line Following Sensor 5 Array

High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...