Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
LM35 is an integrated analog temperature sensor whose electrical output is proportional to Degree Centigrade. LM35 Sensor does not require any external calibration or trimming to provide typical accuracies. The LM35’s low output impedance, linear output, and precise inherent calibration make interfacing to readout or control circuitry especially easy.
As such no extra components required to interface LM35 to ADC as the output of LM35 is linear with 10mv/degree scale. It can be directly interfaced to any 10 or 12 bit ADC. But if you are using an 8-bit ADC like ADC0808 or ADC0804 an amplifier section will be needed if you require to measure 1°C change.
LM35 can also be directly connected to Arduino. The output of LM35 temperature can also be given to comparator circuit and can be used for over temperature indication or by using a simple relay can be used as a temperature controller.
The LM35 device is rated to operate over a −55°C to 150°C temperature range, while the LM35C device is rated for a −40°C to 110°C range (−10° with improved accuracy). The LM35-series devices are available packaged in hermetic TO transistor packages, while the LM35C, LM35CA, and LM35D devices are available in the plastic TO-92 transistor package. The LM35D device is available in an 8-lead surface-mount small-outline package and a plastic TO-220 package.
| General Specification | |
| Package/Case | TO-92-3 |
| Mounting Type | Through Hole |
| Sensor Type | Temperature Sensor |
| Output Type | Analog Voltage |
| Maximum Supply Voltage (V) | 30 |
| Minimum Supply Voltage (V) | 4 |
| Operating Temperature Range (°C) | -55 to 150 |
| Shipment Weight | 0.008 kg |
| Shipment Dimensions | 8 × 5 × 3 cm |
| Shipment Dimensions | 6 × 5 × 4 cm |
| Weight (Kg) | 40 |
| Cable Length (cm) | 80 |
| Cable Weight (gm) | 34 |
| Shipment Weight | 0.05 kg |
| Shipment Dimensions | 10.3x10.5x6.5 |
1 x LM35 Temperature Sensor
The latest price of LM35 Temperature Sensor in Bangladesh is BDT 95 You can buy the LM35 Temperature Sensor at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-1063
Temperature Control Range(°C): -50 to +110 Resolution @-9.9°C to +99.9°C: 0.1°C Resolution @all temperatures: 1°C Accuracy: 0.1°C Refresh Rate(s): 0.5 Supply Voltage(V): 12 Measuring Inputs: NTC10K Cable Length: 0.5 Meter Output Type: 1 Channel Relay Output Capacity: 10A
Reference: RBD-1756
TMP36 Temperature Sensor Low Voltage Temperature Sensors
Reference: RBD-2214
EMG muscle sensor V3.0 with cable and electrodes Measures the electrical activity of muscles High signal quality for accurate and reliable measurement Adjustable gain and filtering for signal conditioning Compatible with various types of microcontrollers and data acquisition systems Comes with reusable electrodes and a 3.5mm jack cable for easy connection
Reference: RBD-1766
Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.
Reference: RBD-0559
Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA 0-5V to 4-20mA Linear Conversion
Reference: RBD-2130
9DOF IMU Breakout9 can capture nine different types of motion or orientation of the 3-axis accelerometer to obtain the relevant data magnetic orientation and angular velocity that is three-axis gyroscope + triaxial accelerometer three-axis magnetic field +
Reference: RBD-1974
Brand: DFRobot
One-click learn Machine Learning Enabled Onboard Screen Extreme Performance
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0720
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant. RoboticsBD
Reference: RBD-1671
ESP32 Bluetooth Wi-Fi development board, support NodeMCU / Arduino DHT11 temperature and humidity sensor CP2104 communication chip USB TO TTL Micro USB port Soil probe (long) soil temperature and humidity detection module 18650 Lithium Battery Holder Powered (Battery is not included)
Reference: RBD-2221
HB100 X 10.525GHz Microwave Sensor 2-16M Doppler Radar Human Body Induction Switch Module For Arduino
Reference: RBD-1835
Input current (RMS): 50A. Work temperature: -25℃～+70℃. Storage temperature: -30℃～+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.
Reference: RBD-1377
Module Name:CJMCU-4541 Sensor: MICS-4514 Type: Carbon Monoxide Nitrogen Oxygen Sensor
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-0722
8-Megapixel native resolution high-quality Sony IMX219 image sensor Cameras are capable of 3280 x 2464 pixel static images Capture video at 1080p30, 720p60 and 640x480p90 resolutions All software is supported within the latest version of Raspbian Operating System No Infrared filter making it perfect for taking Infrared photographs or photographing objects...
Reference: RBD-1243
Resolution: 500dpi Supply current: <60mA Supply voltage: 3.3V Fingerprint image entry time: <1.0 seconds Peak current: <60mA
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1757
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-0679
Sensitivity to Ammonia, Sulfide and Benzene steam Sensitive for benzene, alcohol, smoke Fast response and recovery Adjustable sensitivity. RoboticsBD Signal output indicator Output voltage boosts along with the concentration of the measured gases increases.
Reference: RBD-2083
Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-2172
Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD Force Sensitive Resistor Square High Quality
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-0668
Crystal 32.768KHz, matching capacitance 6pF DS1302 8-pin SMD homemade chips Seconds, Minutes, Hours, Day of Month, Day of Week, and Year Operating temperature: 0 degree — 70 degree. RoboticsBD
Reference: RBD-1227
Object Scanning Device with USB 2.0 Interface / CMOS Sensor
Reference: RBD-2146
Operating voltage:3.3V/5V Sensitivity: Adjustable via a potentiometer Input Signal: Resistance, NOT Conductivity Output Signal: Voltage, analog reading Finger contact material: Nickel
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0674
Model: MQ-5 Operating Voltage: 5V DC Operating Temparature:-20~40 degree celcius
Reference: RBD-0568
Fixed focus lens on-board Improved resolution – 8-Megapixel native resolution sensor-capable of 3280 x 2464 pixel static images Supports 1080p30, 720p60 and 640x480p90 video Size 25mm x 23mm x 9mm Weight just over 3g Connects to the Raspberry Pi board via a short ribbon cable (supplied) Camera v2 is supported in the latest version of Raspbian, Raspberry...
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-1175
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-0413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-0169
Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.
Reference: RBD-1362
1N4742 12V Zener Diode DO-41 glass case Approx. 0.35 gram
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0133
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0041
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-0104
Chip built-in 16bit AD converter, 16-bit data output Driver Chip: MPU6050 Operating Voltage: 3-5V DC Communication: I2C/IIC Protocol Gyro Range: ± 250, 500, 1000, 2000 °/s Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-0147
Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
