Reference: RBD-1192

Hall Effect Sensor 6851/A3144

Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.

Reference: RBD-1541

37 In 1 Sensor Module Board Set Kit For Arduino with Box

For beginners who are interested in Arduino A complete set of Arduino’s most common and useful electronic components Infrared sensor receiving module Laser sensor module Temperature and humidity sensor module Infrared sensor module 5v relay module Obstacle avoidance sensor module.

Reference: RBD-0417

Force Sensor Resistor Square 38.1mm

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-0149

Flame Sensor Fire Detection Module

Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...

Reference: RBD-0672

MQ-3 Alcohol Gas Sensor

Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output:  0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.

Reference: RBD-2215

4 Channel Infrared Line Following and Obstacle Sensor

Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.

Reference: RBD-1249

Shaftless Vibration Motor D34

Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA

Reference: RBD-0663

TTP223B Digital Touch Sensor Capacitive Touch

Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD

Reference: RBD-2095

Infrared Obstacle Avoidance Sensor Module

Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...

Reference: RBD-1206

RPLIDAR A2 360° Laser Range Scanner

Scanning Range: 18M Radius Detection Range:  12M Radius 4cm Ultra-thin Ideal for all kinds of service robot. 8000 times sample rate, the highest in the current economical LIDAR industry 360-degree laser range scanning Low Noise, Brushless Motor New Non-contact Drive OPTMAG Original Design, prolong the life-span Class 1 Laser Safety Standard High-speed...

Reference: RBD-0291

Sound Sensor Module for Arduino

Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.

Reference: RBD-2139

GSR Skin Sensor CJMCU-6701 Analog SPI Module

GSR Skin Sensor CJMCU-6701 Analog SPI Module Measures the electrical conductance of the skin (Galvanic Skin Response) Reflects human emotional activity and stress levels Suitable for creating emotion-related projects and sleep quality monitors Utilizes a precise 12-bit AD converter for accurate readings

Reference: RBD-1111

Geiger Counter Kit Nuclear Radiation Detector Gamma Ray Build Radiation Monitoring Station

This is one open-source Geiger Counter project which could be used to detect nuclear radiation. The schematic and code and other helpful files are listed in this package. All the codes are designed and tested on this kit, these materials are useful for DIY Geiger Counter Kit Nuclear Radiation Detectors or Radiation Monitoring Stations. Note: The kit comes...

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-2076

5mm Two-Color LED Module

Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150

Reference: RBD-0414

Waterproof DS18B20 Digital Thermal Probe or Sensor

A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...

Reference: RBD-2149

50kg Half-bridge Experiments Body Scale Load Cell Sensor

Capacity (Kg): 50. Output Sensitivity (mv/v): 1.0±0.1. Nonlinearity (%FS): 0.03. Repeatability (%FS): 0.03. Input Resistance (Ω): 1000. Insulation Resistance (MΩ): ≥5000.

Reference: RBD-0222

35mm Piezo Ceramic Elements Sound Sensor

Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound

Reference: RBD-1766

ADXL345 3-axis Digital Gravity Sensor Acceleration Module

Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.

Reference: RBD-1179

LM35 Temperature Sensor Waterproof

Temperature measuring range: 0...100°C Typical Input Voltage:3.3VDC,5VDC Operating Current:60uA Interface: Analog ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase unless you're confident that you can use it successfully.

Reference: RBD-0574

Honeywell HMC5983 Temperature Compensated Three-Axis Digital Compass

3-Axis Magnetoresistive Sensors and ASIC in a 3.0x3.0x0.9mm LCC Surface Mount Package Temperature Compensated Data Output and Temperature Output Automatic Offset Compensation. RoboticsBD

Reference: RBD-2071

SS49E Linear Hall Effect Sensor Module

Type: Magnetic Sensor Module Mainly Compatible with: Ardunio

Reference: RBD-0492

Omron Proximity Sensor Switch E2E-X5MF2-Z

Proximity-sensing / Diffuse Type Voltage: DC 6-36V Current: 300mA Sensory Distance: 5mm

Reference: RBD-2170

100mm x 100mm Medium Magnetic Field Viewing Paper

Visualize magnetic fields with ease using the field paper Large size of 100mm x 100mm for a clear and detailed view Micro-encapsulated film enables visualization of magnetic fields Suitable for use with any magnet Lightweight and compact for easy handling and storage

Reference: RBD-2098

Big Microphone Sound Sensor Module

Big Microphone Sound Sensor Module  Sound Detection Sensor Module High Sensitive Voice Sensor

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-2221

10.525GHz HB100X Microwave Sensor Module

Microwave sensor module Uses 10.525 GHz band to detect movement Easy to use, can be connected directly to a microcontroller Built-in amplifier Ideal for use with a microcontroller Widely used in industrial, transportation, and civil devices

Reference: RBD-0424

Si7021 Industrial High Precision Humidity Sensor I2C Interface for Arduino

SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface

Reference: RBD-1854

Resistive Film Pressure Sensor Module Pin Header Analog Signal 200mm

This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.

Reference: RBD-1860

KS-RG22 High Precision Electric Eye Color Sensor

Model KS-RG22 Coaxial reflection type Supply voltage DC10-30V±10%