How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
7 Color Flashing LED Module is a module with an auto-flash led that can flash up to 7 colors. No programming needed. Just connect it with power supply and it’ll work. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
Note: Product images/ Components brand may vary from actual product as our stock rotates.
Note: PCB might be different from the picture as per stock
| General Specification | |
| Standard Forward Voltage | 3.0-4 .5 V |
| Shape | Round DIP type |
| Diameter(mm) | 5 |
| Color | pink yellow green (high brightness) |
| Lens type | white mist |
| Lenght(mm) | 31 |
| Width(mm) | 17 |
| Weight(g) | 3 |
| Shipment Weight | 0.005 kg |
| Shipment Dimensions | 12 × 8 × 2.5 cm |
Please allow 5% measuring deviation due to manual measurement.
1 x 7 Color Flashing LED Module
The latest price of 7 Color Flashing LED Module in Bangladesh is BDT 55 You can buy the 7 Color Flashing LED Module at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0769
Size: 5mm Color: BLUE Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0770
Size: 5mm Color: Yellow Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-0980
Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.
Reference: RBD-1041
PCB Size: 60 x 20 x 13.5 (LxWxH)mm. Color: red, yellow, green LED Size: 10mm x 7. Brightness: Normal brightness. Voltage: 5V. Interface: common cathode red yellow green control.
Reference: RBD-3317
The MLX90333 Handle 3D Joystick Absolute Position Sensor Module is designed for precise and reliable 3D position sensing in various applications. Operating within a voltage range of 4.5V to 5.5V, this module uses advanced 3D magnetometer technology to accurately detect joystick movements or linear positions. With multiple output modes, including analog,...
Reference: RBD-3280
The GY-NEO-6M V2 GPS Module is a high-performance GPS receiver designed for accurate navigation and positioning applications. This module comes equipped with a ceramic antenna, onboard EEPROM for data storage, and an LED signal indicator for real-time status updates.
Reference: RBD-2554
Type: Operational Amplifier Test Board Material: PCB Size: Approx. 92 x 57 x 17mm / 3.62 x 2.24 x 0.67in Working Voltage: DC 12V Working Current: >100mACompatible Op-Amp Models: Single Op-Amp: LM741, LF356, NE5534, TL071, TL081, OP07, and other standard package single op-amps. Dual Operational: LM358, NE5532, TL072, TL082, MC1458, RC4558, OP275, AD827,...
Reference: RBD-0358
Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins
Reference: RBD-2741
Module mounts an 8MB serial flash chip for easy use with breadboards.
Reference: RBD-2317
5-way tactile navigation switch with north, south, east, west, and center push functionality Compact design ideal for creating directional control interfaces Mini joystick-like operation for intuitive user input Compatible with breadboards and perfboards with slight pin adjustments Lightweight and easy to integrate into DIY and prototyping projects
Reference: RBD-2359
433 MHz wireless transceiver module with SMA antenna for stable, long-range communication. Powered by CC1101 chip from Texas Instruments, ensuring reliable performance. Supports FSK, OOK, ASK, and MSK modulation with up to 500kbps data rate. Seamless transmission over 350m range with low power consumption. Ideal for smart homes, industrial IoT, scientific...
Reference: RBD-1959
Single supply voltage 3.4V – 4.5V HW-353A SIM900A Module Development Board GSM GPRS The keypad and SPI display interface will give you the flexibility to develop customized applications. Serial port and Debug port can help you easily develop your applications. One audio channel includes a microphone input and a speaker output. Programmable General Purpose...
Reference: RBD-2306
WS2812B RGB LED 12-Bit Ring with integrated drivers for vibrant lighting effects Features 12 WS2812 5050 RGB LEDs capable of producing 16,777,216 true colors Single data line with precise timing protocol for individual LED control Compact design with 30mm outer radius and 15mm inner radius Operates at 5V, ideal for dynamic lighting applications and DIY...
Reference: RBD-3206
The Metal Motor Servo Tester ESC Checker Master is a professional-grade tool designed to test and calibrate servos and electronic speed controllers (ESCs) for RC drones, cars, boats, and helicopters. With its durable aluminum alloy construction and versatile functionality, this tester allows you to adjust and synchronize multiple servos or ESCs with ease....
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1594
29mm diameter 10 LED Dimmable 50-degree viewing angle
Reference: RBD-1564
High voltage resistant terminal. Support solar charging. Support undervoltage protection. Support short circuit protection.
Reference: RBD-3272
The PCF8563 RTC Module is a low-power real-time clock and calendar chip designed for accurate timekeeping in embedded systems and microcontroller applications. This module communicates using the I2C bus, making it easy to interface with microcontrollers such as Arduino, Raspberry Pi, ESP32, and STM32. Equipped with alarm, timer functions, and a...
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-1578
Support serial AT command Support re-programmable, OTA firmware update Seamless transparent transmission between serial and WiFi Built-in HTTP Web Server, support configure parameters by web page
Reference: RBD-1137
Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...
Reference: RBD-2077
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:3mm Wavelength:571nm + 644nm Beam Angle:150
Reference: RBD-2858
Multi-Sensor Support: Works with various sensors like NTC thermistors, TCRT5000 line followers, and force sensors. Precise Control: Dual potentiometers for fine-tuning sensor thresholds. Wide Voltage Compatibility: LM393 chip ensures adaptability to diverse power sources. Compact & Durable Design: Integrates seamlessly into projects with a robust build.
Reference: RBD-0040
Bluetooth 2.0 Module Based on CSR BC04 Chip – Ideal for reliable wireless communication. Slave Mode Only – Perfect for receiving data from smartphones or other master devices. Wide Operating Voltage (3.3V to 6V) with onboard regulator for easy integration. Built-in 2.4GHz PCB Antenna – Supports wireless range up to 10 meters. Simple UART Interface (VCC,...
Reference: RBD-3591
Enhance your Arduino Nano projects with the NANO3.0 Data Logging Expansion Board (Welded)—a feature-rich shield designed to bring time-stamped data storage functionality to your embedded systems. With its built-in SD card interface, Real-Time Clock (RTC), and 3.3V level shifter, this board is perfect for applications involving environmental monitoring,...
Reference: RBD-1928
Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.
Reference: RBD-2566
With this High-Power MOSFET module you can easily use the double mosfet through the separate connections for power supply, switch pins and signal pins.The LED on the module indicates whether the MOSFET is switched on. This board is particularly useful for controlling a large LED strip (one color) or a motor (in one direction) by using. PWM.
Reference: RBD-2557
Introducing the Battery Level Display Module, a versatile and user-friendly device based on battery-style digital tube LED technology. This module features 10 light segments and incorporates the TM1651 driver chip for simplified control, requiring only two signal lines along with VCC and GND connections. It is specifically designed for displaying battery...
Reference: RBD-3443
The AD7705 Analog-to-Digital Converter (ADC) Module is a high-precision, low-frequency measurement solution designed for direct interfacing with microcontrollers or DSP-based systems. Featuring a 16-bit resolution, dual-channel input, and SPI communication, this module allows for flexible gain settings, signal polarity adjustment, and update rate...
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-2054
Multi-functional transistor tester. Automatic detection of NPN and PNP transistors, FET, diodes, dual diode, thyristor and SCR. Automatic identification of the transistor pinout. Can be used as a Square signal generator. Can be used as a PWM signal generator.
Reference: RBD-0986
Ultra-thin design & adhesive backing provides easy integration to any project. Excellent price-performance ratio. Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting.
Reference: RBD-3166
The GY-SI5351 Clock Signal Generator Module is a versatile and precise clock generation device, capable of producing multiple independent frequencies with minimal error. Controlled via I2C, this module is perfect for applications requiring precise frequency synthesis for audio, video, communication, and general electronic projects. With three independent...
Reference: RBD-2718
Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs
Reference: RBD-1060
Perfectly fit on the extruder Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-1298
Overtemperature Protection Logical “0” Input Voltage Up To 1.5 V (High Noise Immunity) Internal Clamp Diodes. Featuring Unit rode L293 and L293D Wide Supply-Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs
Reference: RBD-3264
The 4x4 Matrix Keypad Module is a compact and efficient input device designed for microcontroller projects, offering 16 push buttons arranged in a 4-row x 4-column configuration. This non-encoded matrix keypad enables simple and flexible data entry for various applications, such as password authentication, menu navigation, and user interfaces. Each button...
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0949
Operating Voltage : 2.5 ~ 4V Operating Current : 130 ~ 220mA Flow Rate : 80 ~ 120 L/H Maximum Lift : 40 ~ 110 mm Outlet Outside Diameter: 7.5 mm Outlet Inside Diameter: 5 mm
Reference: RBD-0286
3D Printed Bumper: Designed for Arduino Uno R3 boards Short Circuit Protection: Prevents accidental short circuits on conductive surfaces Secure Press-Fit: Ensures a snug fit while allowing easy removal Scratch Protection: Protects surfaces from scratches caused by the board Arduino Uno R3 is not included.
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-1300
Size: 5mm Color: BLUE Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0770
Size: 5mm Color: Yellow Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-0219
Resistance: 1 Mohm Tolerance: 5% Max. Working Voltage: 250V Temperature Coefficient of Resistance: 50PPM/°C
