Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
TDA2030 is an audio amplifier which provides an output power of 14 Watts. It has internal protection system against short-circuits and overloads which limits the dissipated power. It is basically designed for use in applications requiring a class AB amplifier of a low frequency. TDA2030 audio amplifier amplifies the audible signals from any audio device for example microphone by enhancing its volume when that sound is played on a speaker. RoboticsBD
Pinout diagram is very simple and it contains only five pins.
| General Specification | |
| Package/Case | PDIP-3 |
| Minimum Supply Voltage (V) | 6 |
| Maximum Supply Voltage (V) | 22 |
| Product Type | TDA2030A 18 W hi-fi amplifier and 35 W driver |
| Operating Temperature Range (°C) | –40° C to +150° C |
| Mounting Type | Through Hole |
| Shipment Weight | 0.005 kg |
| Shipment Dimensions | 3 × 3 × 3 cm |
1 x TDA2030A
The latest price of TDA2030A in Bangladesh is BDT 18 You can buy the TDA2030A at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing Current Stock: 741CN
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-1324
Operating voltage: 2.5V-5.5V Maximum output power: 3W x 2 PCB size is about: length 30mm width 22mm overall height after installed is about 16mm Built with switch Potentiometer, can adjust the volume & control power switch freely! Flexible assembly usage.
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-1750
Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV
Reference: 1818
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing Current Stock: 741CP
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-1867
Original TDA7297 core technology Easy Plug and Play Operation Dynamic operating Voltage Range: 8 to 16V High fidelity Dual 15W output.
Reference: RBD-1289
IC 74LS164 8-bit Parallel-Out Serial Shift Register with Asynchronous Clear Package / Case: 14-DIP
Reference: RBD-1298
Overtemperature Protection Logical “0” Input Voltage Up To 1.5 V (High Noise Immunity) Internal Clamp Diodes. Featuring Unit rode L293 and L293D Wide Supply-Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs
Reference: RBD-1011
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation Common mode input voltage range includes ground, allowing direct sensing near ground Input offset voltage is typical 3mV...
Reference: RBD-2274
PWM controller IC used for power supplies, motor control, and lighting control. Offers high efficiency, flexible configuration, and precise output control. Widely available, cost-effective, and commonly used in a variety of electronic designs.
Reference: RBD-1275
UL recognized Operating temperature range from -40°C to 85°C Automatic power fail to detect and switch circuitry Timekeeping current of 300nA Completely manages all timekeeping functions 56byte, battery backed, general purpose RAM with unlimited writes A programmable square wave output signal Simple serial port interfaces to most microcontrollers
Reference: RBD-1435
IC Name: SG3525A SG 3525 PWM IC based Power Inverter Package/Case: DIP-16
Reference: RBD-1277
Advanced Process Technology Ultra Low On-Resistance Dynamic dv/dt Rating 175°C Operating Temperature Fast Switching Fully Avalanche Rated Lead-Free
Reference: RBD-1883
IC Name: 74LS83A Package/Case: DIP-16 4-BIT BINARY FULL ADDER WITH FAST CARRY LOW POWER SCHOTTKY
Reference: RBD-1318
Low saturation voltage Over temperature protection High noise immunity Applications: Motor Drive & Control Operating Supply Voltage Up To 46 V Total Dc Current Up To 4 A Low Saturation Voltage Overtemperature Protection
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-0767
Input Voltage(Max.) : 5V Resistance: 42 Ω Resonance Frequency: 2048 Hz Body Size : 12 x 8mm Pin Pitch: 6mm External Material: Plastic; Color: Black
Reference: RBD-0993
Resistance: 1k Ohm Tolerance: 10 % Temperature coefficient: ±100 ppm/ºC Operating temperature range: -55ºC to +125ºC Mounting type: Through-hole
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-1723
Model: XKT-412. Input Voltage: 12V. Output Voltage: 5V. Operating Current: 1.2-2 A. Receive Coil: 3mm, the receiver output 5V / 1A current Normal Use Distance: 2 ~ 10mm Operating Current: 1.2-2 A.
Reference: RBD-1876
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 1.8. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. Model: HS 121800
Reference: RBD-1495
Capacitance: 47uF Voltage: 16V Mounting: Through Hole Material: Aluminum Tolerance: ±20 %
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-1360
PN junction rectifier diode. One direction flow of Current. Used for conversion of AC power to DC. 1N 4007 is electrically compatible with other rectifier diodes Used instead of any of the diode belonging to 1N400X series
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0280
Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0840
Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown
Reference: RBD-1001
IC Name: LM339 Package/Case: DIP-14 LM339N is a quad voltage comparator IC. It compares the input voltages at four independent input pins and outputs a high or low signal based on the comparision. It is commonly used for voltage sensing and triggering events in various electronics projects.
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing Current Stock: 741CN
