Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Isolation of low-level control signals: The 4N35 optocoupler can be used to isolate low-level control signals from high-power or high-voltage signals. This provides protection for sensitive control circuits from electrical noise, surges, or other disturbances.
Interfacing between digital and analog circuits: The 4N35 optocoupler can be used to interface between digital circuits and analog circuits, allowing them to communicate with each other while maintaining electrical isolation.
Motor control: The 4N35 optocoupler can be used in motor control applications to provide isolation between the control circuit and the power circuit, helping to prevent electrical noise from affecting the control signals.
Power supply regulation: The 4N35 optocoupler can be used in power supply regulation applications to provide isolation between the control circuit and the power circuit, helping to prevent electrical noise from affecting the control signals.
Protection against electrical noise: The 4N35 optocoupler can be used in applications where electrical noise is a concern, such as in data communication systems, to provide electrical isolation and protect the control signals from interference. This helps to improve the signal-to-noise ratio and overall performance of the system.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Package/Case | PDIP-8 |
| Minimum Supply Voltage (V) | 4.5 |
| Maximum Supply Voltage (V) | 5.5 |
| Product Type | Optocoupler, Phototransistor Output, with Base Connection |
| Operating Temperature Range (°C) | 0 to 70 |
| Mounting Type | Through Hole |
| Shipment Weight | 0.005 kg |
| Shipment Dimensions | 3 × 3 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 4N35 Optocoupler
The latest price of 4N35 Optocoupler in Bangladesh is BDT 40 You can buy the 4N35 Optocoupler at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0133
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
Reference: RBD-0280
Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-1266
It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...
Reference: RBD-1736
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-1768
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-1780
1. MINI USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 17.5 mm .
Reference: RBD-1781
1. Micro USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 16 x 14 mm .
Reference: RBD-1782
1. USB Type B Female ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 20 mm .
Reference: RBD-1416
High performance RISC CPU Only 35 single word instructions to learn All single cycle instructions except for program branches which are two-cycle
Reference: RBD-1001
IC Name: LM339 Package/Case: DIP-14 LM339N is a quad voltage comparator IC. It compares the input voltages at four independent input pins and outputs a high or low signal based on the comparision. It is commonly used for voltage sensing and triggering events in various electronics projects.
Reference: RBD-1982
14 pins. JDEC compliant. Molded notch for proper orientation. Easy to insert and remove ICs.
Reference: RBD-1278
Wide supply voltage range from 2.0 V to 6.0 V CMOS low power dissipation High noise immunity Latch-up performance exceeds 100 mA per JESD 78 Class II Level B
Reference: RBD-1277
Advanced Process Technology Ultra Low On-Resistance Dynamic dv/dt Rating 175°C Operating Temperature Fast Switching Fully Avalanche Rated Lead-Free
Reference: RBD-1275
UL recognized Operating temperature range from -40°C to 85°C Automatic power fail to detect and switch circuitry Timekeeping current of 300nA Completely manages all timekeeping functions 56byte, battery backed, general purpose RAM with unlimited writes A programmable square wave output signal Simple serial port interfaces to most microcontrollers
Reference: RBD-1299
Size: 5mm Color: White Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-0842
Maximum Repetitive Peak Reverse Voltage (VRRM): 1000V. Maximum RMS voltage (VRMS): 700V. Maximum Average Forward Rectified Current(IF(AV)): 3A.
Reference: RBD-1003
Fixed output voltage is 5V Output current is 0.5A Dropout voltage is 2V Maximum DC input voltage is 35V Output transition SOA protection Output voltage tolerance is 4%
Reference: RBD-1102
PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...
Reference: RBD-1189
Wavelength: 850nm Emission Distance: 7 Meters / 23Ft Voltage: DC 1.2-1.3V Polarity: Anode (Longer Part) | Cathode (Shorter Part)
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-1360
PN junction rectifier diode. One direction flow of Current. Used for conversion of AC power to DC. 1N 4007 is electrically compatible with other rectifier diodes Used instead of any of the diode belonging to 1N400X series
Reference: RBD-1001
IC Name: LM339 Package/Case: DIP-14 LM339N is a quad voltage comparator IC. It compares the input voltages at four independent input pins and outputs a high or low signal based on the comparision. It is commonly used for voltage sensing and triggering events in various electronics projects.
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing Current Stock: 741CN
