

In recent years 2022, due to a shortage of chips, some of the SIM modules have been recycled from Phones. So these modules have used mark due to the recycling procedure, but all modules are QC tested from China. Please use 3.3V while wiring
Condition: Refurbished
Note: If you want to buy the new SIM800L Module Click here.
This is Small SIM800L GPRS GSM Module Micro SIM Card Core Board Quad-band TTL Serial Port with the antenna, in this module two antennas have been included.
SIM800L GSM/GPRS module is a miniature GSM modem, which can be integrated into a great number of IoT projects. You can use this module to accomplish almost anything a normal cell phone can; SMS text messages, make or receive phone calls, connecting to the internet through GPRS, TCP/IP, and more! To top it off, the module supports quad-band GSM/GPRS network, meaning it works pretty much anywhere in the world
First is made of wire (which solders directly to NET pin on PCB) – very useful in narrow places. Second – PCB antenna – with double-sided tape and attached pigtail cable with IPX connector. This one has better performance and allows to put your module inside a metal case – as long the antenna is outside. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Caution: Use a resistor divider circuit before interfacing it with Arduino to avoid the damage to the module.
This SIM800L breakout board is ideal for projects that needs to save space. This board draws a maximum of 2 A with an input voltage of 3.7 V to 4.2 V. This means you must not connect its pins directly to a 5 V Arduino! It doesn't even run on 3.3 V.
The solution is either to use a regulator or just have the SIM800L draw from a Li-Po (cellphone) battery.
Antennas are essential for this kind of module especially if your project is indoors. Without an antenna, there would not be enough transmitting power for the SIM800L to perform GSM services such as calls and SMS.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
IC Chip | SIM800L |
Operating Voltage (VDC) | 3.7 ~ 4.2 |
Peak Current (A) | 2 |
Shipment Weight | 0.01 kg |
Shipment Dimensions | 9 × 6 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x SIM800L Mini GPRS GSM Module
1 x PCB Antenna.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of SIM800L Mini GPRS GSM Module in Bangladesh is BDT 450 You can buy the SIM800L Mini GPRS GSM Module at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
Reference: RBD-0579
Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-1557
USB communication, no need write code Support PC software automation Double antenna Support quad-band, universal worldwide Support 2G/3G/4G Automatically connect to the network Adaptive frequency
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-1134
Easy to Assemble Comes With all Components Operating Voltage: 5VDC Operating Current: 200mA Compatible With Arduino and Raspberry Pi
Reference: RBD-1962
ESP32-S2-DevKitM-1 Equipped with ESP32-S2-MINI-1 module Easy interfacing Integrates ESP32-S2FH4 chip. PCB antenna 4 MB SPI flash.
Reference: RBD-1337
Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600 Note: Relay might be different from the picture as per stock
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1928
Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.
Reference: RBD-1578
Support serial AT command Support re-programmable, OTA firmware update Seamless transparent transmission between serial and WiFi Built-in HTTP Web Server, support configure parameters by web page
Reference: RBD-0284
Gain: 2.0dBi-2.5dBi Antenna connector: SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes
Reference: RBD-1552
Working Frequency: 868 MHz Distance: 8000m RF IC: SX1276
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-2176
LoRa module based on Semtech SX1262 RF chip Supports automatic relay networking Long transmission distance up to 10 km Low power consumption Small size
Reference: RBD-0369
Brand: SparkFun Electronics
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-0697
Driver Chip: CH340G Supports all basic windows versions. The adapter plate integrated 1000μF solid capacitors to ensure the current supply The power supply will not be a problem to make WIFI module crashes unresponsive. Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall. Working voltage: 4.5V – 5.5V (Onboard...
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-2136
Very Few External Components Excellent Receiver Sensitivity and Robustness to Interference. Programmable Output Power Up to 4.5 dBm. High-Quality Construction
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-1604
Supports Digital terrestrial video and radio program recording (records digital terrestrial TV on PC or Laptop). The included Input Terrestrial Antenna will offer stable TV signal. Supports Real Time digital video recording and broadcasting. Supports Watching DVB-T digital TV and listen to DAB and FM radio. Full DVB-T bandwidth reception (at 6 / 7 /...
Reference: RBD-0103
This is M177 NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01...
Reference: RBD-0733
Connects Devices & Antennas: Ideal for WiFi, Bluetooth, and nRF devices to 2.4GHz antennas. Enhanced Usability: 150mm length (compared to standard 100mm) provides more flexibility for enclosure integration. Reliable Signal: 50Ω impedance ensures efficient signal transmission. Durable Construction: Built with high-quality materials for long-lasting...
Reference: RBD-1641
Product: GSM Antenna Color: Black SMA male straight 5cm 900-1800MHz radio antenna. Frequency: 900MHz – 1800MHz Maximum Power: 50W Length: 5cm/1.97 inch
Reference: RBD-0624
Operating Voltage: DC 2V- 9V Operating frequency: 85MHZ - 115MHZ Output Impedance: 50 ohms
Reference: RBD-1529
Model:SX1278ZTR4 SX1278 433mhz module spread spectrum low power serial port module LoRa wireless module Range: 3-5 KM (line of sight) Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃
Reference: RBD-0201
QUICK OVERVIEW Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module Receiver: FS-IA10B Default Mode: Mode-2 Input Power: 12V DC (1.5V x 8 AAA Battery) Bidirectional System Frequencies-Hopping Omni-directional High Gain Antenna Low Power Consumption
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-1670
The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA
Reference: RBD-1424
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-0441
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD
Reference: RBD-2010
Capacity (mAh): 960-1500 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-0653
Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-0672
Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output: 0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.
Reference: RBD-2088
Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated
Reference: RBD-1490
Capacitance: 1uF Voltage: 50V Mounting: Through Hole Material: Aluminum Tolerance: ±20 %